manualshive.com logo in svg

Stihl TS 410, Инструкция по эксплуатации

Поделиться
Скачать
Stihl TS 410 Скачать руководство пользователя страница 26

Versions with decompression valve

5

370BA101 KN

► Press the button (5) of the decompression

valve before each starting procedure

For all versions

6

370BA102 KN

► Press the bulb (6) of the manual fuel pump

7‑10 times – even when the bulb is still filled

with fuel

13.1

Starting

370BA092 KN

► Place the cut-off machine carefully on the

ground, ensuring that the abrasive wheel can‐

not touch the ground or any objects. There

must not be anyone within the swivel range of

the cut-off machine

► Make sure you have a firm footing

► Press the cut-off machine firmly against the

ground, holding the handle with your left hand,

thumb wrapped round the handle

► Press the cut-off machine against the ground

with the right knee on the shroud

► Pull the starter grip slowly with your right hand

until you feel it engage – then give it a brisk

strong pull – do not pull out the starter rope all

the way

NOTICE

Do not let the starter grip snap back – it may

break! Guide it back into the housing in the

opposite direction so that it can rewind properly.

13.2

When the engine has turned

over for the first time

4

370BA057 KN

Choke

► Set the choke lever (4) to 

f

► Press the button of the decompression valve

(depending on version)

► continue cranking

13.3

Once the engine is running

► Squeeze throttle trigger fully and let engine

run at full throttle for approx. 30 s

English

13 Starting / Stopping the Engine

26

0458-370-8321-C

Содержание TS 410









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды