manualshive.com logo in svg

Stihl TS 410, Инструкция по эксплуатации

Поделиться
Скачать
Stihl TS 410 Скачать руководство пользователя страница 12

3.7

Cutting concrete pipe

A

002BA557 AM

The procedure is dependent on the outer diame‐

ter of the pipe and the maximum possible cutting

depth of the abrasive wheel (A).

► Secure pipe against vibrations, slipping and

rolling away

► Note weight, tension and direction of fall of the

part to be severed

002BA528 

AM

► Determine and mark direction of cut

► Determine sequence of cuts
Outer diameter is smaller than the maximum cut‐

ting depth

002BA558 AM

► Make one cut from the top to the bottom
Outer diameter is greater than the maximum cut‐

ting depth
Plan first, then cut. Several cuts are needed –

correct sequence is important.

► Turn guard at rear stop

002BA560 

AM

► Always start at the bottom, use the upper

quarter of the abrasive wheel for cutting

002BA561 

AM

► Use the upper quarter of the abrasive wheel

for cutting the opposite lower side.

002BA562 

AM

► First lateral cut on the top half of the pipe

002BA563 

AM

► Second lateral cut in the marked area – never

cut into the area of the last cut, to ensure a

firm hold on the part of pipe to be cut

Only make the last top cut once all bottom and

lateral cuts have been made.

English

3 Sample Applications

12

0458-370-8321-C

Содержание TS 410









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды