Stihl MS 171 Скачать руководство пользователя страница 94

Страница: 94 / 102

MS 171, MS 181, MS 211

14.8.2 Removing and Installing

– Remove the handle frame,

11.4

Pry out the tank vent (1) as
shown (arrow).

Always install a new tank vent.

– Disconnect the fuel hose (1),

check and replace if necessary.

Push the new tank vent (2) into
the fuel hose (1) as far as stop.

533RA403 TG

533RA404 TG

– Coat seat of tank vent with STIHL

Press Fluid,

Press the tank vent into its seat
(arrows) in the handle frame (1)
by hand.

– Install the handle frame,

11.4

Push the fuel hose (1) onto the
stub (arrow).

– Reassemble all other parts in the

reverse sequence.

– Tightening torques,

3.5

14.8.3 Manual Fuel Pump

Not installed in all machine
versions. A faulty manual fuel pump
must be replaced.

533RA405 TG

533RA406 TG

– Remove the filter base,

14.2

– Remove the carburetor,

14.3

Pull the fuel hose (1) out of the
guides (arrows).

Check the fuel hose (1), pull it off
the connector (2) and replace if
necessary.

– Install in the reverse sequence.

Press the retaining tabs (arrows)
together and pull out the fuel
pump (1).

– Pull the fuel pump (1) off the fuel

hose (2).

533RA407 TG

533RA408 TG

All manuals and user guides at all-guides.com

Содержание MS 171







































































































Результаты поиска

Содержание MS 171

Отзывы:

Похожие инструкции для MS 171

Бренды по названию

Популярные бренды

Stihl MS 171, Руководство пользователя

Результаты поиска

Содержание MS 171

Отзывы:

Похожие инструкции для MS 171

Бренды по названию

Популярные бренды