Stihl MS 171 Скачать руководство пользователя

Страница: 66 / 102

MS 171, MS 181, MS 211

Pass the lever (1) under the
crossmember (arrow) and
position it at an angle.

Place the switch shaft (1) in
position and engage it in the
lever’s pivot pins (arrows).

Line up the switch shaft (1) and
push it into the right-hand mount
(arrow).

– Position the switch shaft and

lever against the mounts.

533RA253 TG

533RA254 TG

533RA255 TG

Apply screwdriver to ledge
(arrow) above the switch shaft
(1).

Ease the switch shaft (1) into the
guide until it snaps into position.

Insert screwdriver through
opening in the lever (1) and apply
it to the edge (arrow).

Push the lever (1) into the mounts
until it snaps into position.

533RA257 TG

533RA256 TG

Push connector of short circuit
wire (1) into the receptacle on the
switch shaft (arrow) as far as
stop.

The short circuit wire must be
looped (arrow) so that it can move
with the switch shaft.

The wires must be laid close to the
housing and properly seated in the
guides.

533RA258 TG

533RA172 TG

All manuals and user guides at all-guides.com

all-guides.com

Содержание MS 171







































































































Результаты поиска

Содержание MS 171

Отзывы:

Похожие инструкции для MS 171

Бренды по названию

Популярные бренды

Stihl MS 171, Руководство пользователя

Результаты поиска

Содержание MS 171

Отзывы:

Похожие инструкции для MS 171

Бренды по названию

Популярные бренды