Stihl MS 171 Скачать руководство пользователя страница 29

Страница: 29 / 102

MS 171, MS 181, MS 211

Engine

8.1

Muffler / Spark Arresting
Screen

Always check and, if necessary,
repair the fuel system, carburetor,
air filter and ignition system before
looking for faults on the engine.

– Troubleshooting,

Pry the plugs out of the muffler by
means of the tabs (arrows).

Take out the screws (arrows).

– Remove the muffler (1), check

and replace if necessary.

533RA060 TG

533RA061 TG

Remove the heat shield (1).

Spark arresting screen

Use suitable pliers to pull out the
spark arresting screen (1) (if
fitted).

– Clean the spark arresting screen

(1) and replace if necessary.

– Install in the reverse sequence.

Inspect and clean the sealing
faces (arrows),

– Position machine vertically.

533RA062 TG

533RA063 TG

533RA064 TG

Place the heat shield (1) in
position and use the recesses
(arrows) to line it up on the
sealing face of the exhaust port.

– Care place the muffler (1) in

position.

Fit the screws (arrows) and check
correct position of heat shield
again.

– Tighten down the screws

(arrows) firmly.

Push home the plugs (arrows).

– Tightening torques,

3.5

533RA065 TG

533RA066 TG

533RA060 TG

All manuals and user guides at all-guides.com

Содержание MS 171







































































































Результаты поиска

Содержание MS 171

Отзывы:

Похожие инструкции для MS 171

Бренды по названию

Популярные бренды

Stihl MS 171, Руководство пользователя

Результаты поиска

Содержание MS 171

Отзывы:

Похожие инструкции для MS 171

Бренды по названию

Популярные бренды