Stewart MacDonald Bluegrass Resomaster Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 35

background image

page 25

With the strings removed, locate the cover plate and drill its
mounting screw holes. Set the cover plate on the guitar top;
you should see plenty of space (from 3/16" to 1/4") between
the saddle top and the underside of the hand rest

(53)

.

Measure out 3/8" from the soundwell lip at four equally-
spaced points, and place pieces of masking tape as markers.
The cover plate should center between the markers

(54)

,

until an equal amount of wood shows between the cover
plate and the tape at all four points.

Tape the cover plate down, and pencil the outline of the
screw clearance holes onto the top. Remove the cover plate
and drill the holes with a 1/16" bit. Install the cover plate with
the mounting screws, and string the guitar to pitch. This will
be your final check before dismantling the guitar for finish-
ing. Under string tension, our Bluegrass Resomaster showed
a clearance of 1/4" from the top of the strings to the under-
side of the hand rest

(55)

.

Installing the cover plate

53.

Set the cover plate on the guitar top; you should see from

3/16" to 1/4" between the saddle top and the underside of the
hand rest.

54.

The cover plate should center between the markers.

55.

Under string tension, our Blues Resomaster showed a clearance

of 1/4" from the top of the strings to the underside of the hand rest.

«
...
24
25
26
27
28
...
»

Содержание Bluegrass Resomaster




































Отзывы:

Нет отзывов

Похожие инструкции для Bluegrass Resomaster

Бренд: Warwick Страницы: 1

Бренд: Zon Страницы: 21

BRONZE FLYPJ14 N

Бренд: Parker Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды