Stewart MacDonald Bluegrass Resomaster Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 35

background image

page 6

used on the tail block. Follow with spool clamps spaced
evenly around the sides. With spool clamps close on either
side of the waist clamp, you should have good glue squeeze-
out at the waist. Leave the waist clamp in place, and let the
glue dry at least 5 hours.

TIP: Spool clamps

Spool clamps can be made using 8" all thread rods,
wing nuts, drilled wooden spools and cork or
leather lining pads. They’re also available in our
catalog.

Remove the waist clamp temporarily to make room for a
router. With the top glued on, notice that the sides have
gained great stability, even with the waist clamp removed.
Use a flush-cutting ball-bearing router bit to remove the top
overhang in the waist clamp area (any slight burnish marks
left by the ball-bearing will sand off easily). Later, after the
back is glued on, you’ll remove the rest of the top overhang.
For now, the top overhang will match the back overhang,
making it easier to align the spool clamps.

Since you need to remove the cardboard inner form before
you can install the soundwell, sand the back kerfing now
while the body is still relatively rigid.

Re-install the waist clamp from the top side. Place the guitar
on the sandpaper workboard with the back side down. Sand
the back kerfing flush just as you did the top, until the sand-
paper just “kisses” the penciled edge of the sides.

Sanding the back kerfing

The edges of the soundwell connect the top and back, and
kerfing is needed on these edges to provide enough gluing
surface. Install kerfing on the outside of the soundwell, once
again raised a slight 1/64" above the edge

(7)

for flush-sand-

ing on the flat sanding board. Flush-sand only one kerfed
edge of the soundwell — the edge that glues to the top —
and then flush-sand the back edge after the soundwell is
glued to the top. Sanding the soundwell kerfing in two
stages lets you carefully flush-sand the well with the back.

7.

Flush-sand only one kerfed edge of the sound well — the edge

that glues to the top — then flush-sand the back edge after the
sound well is glued to the top.

Installing the soundwell

«
...
5
6
7
8
9
...
»

Содержание Bluegrass Resomaster




































Отзывы:

Нет отзывов

Похожие инструкции для Bluegrass Resomaster

Бренд: Godin Страницы: 3

Бренд: Godin Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды