background image

Pre-Flight Cont.

Clear  Prop!

  -  Before  applying  power  to  the 

model,  clear  and keep clear  of  the  prop arc.  

As  electric  motors  are  capable  of  inflicting 

severe  damage  (more  so  than  their  internal 

combustion  counterparts)  and  may  turn  on 

unexpectedly anytime power is  applied to the 

system.    Respect  the  business  end  of  the 

model (the prop and prop  arc)  treating every 

electric  model  and  propellor  as  if  it  were  a 

loaded gun.

Go  Flying!  -  Enjoy 

SkyBoy  (600)

’s  smooth 

and  docile  flight  characteristics.    You  will 

notice  that

  SkyBoy  (600)

  is  a  very  stable 

airplane.  When built straight, and trimmed for 

level  flight,

  SkyBoy  (600)

  should  return  to 

wings  level  from any  attitude.    We’ve  found

 

SkyBoy  (600)

  to  capture  the  imagination  of 

pilots  both  young  and  old.    With  an 

experienced  instructor  and  a  buddy-box 

system,  we’ve  found

  SkyBoy  (600)

  to  be  a 

very capable four channel sport plane.

If your  first flight was  a bit more exciting than 

you’d  have  liked,  and  your  having problems 

with  erratic flight  performance; pleas  inspect 

your  equipment  and  airframe  for  damage, 

improper installation, and/or twists and warps.  

The most common mistakes  are to try and fly 

with a warped or  twisted wing.    With such a 

fat  chord  and  short  moments,  a  small  warp 

can  cause  big  in-flight  problems.    Make 

certain  that  your  wing  is  straight  before you 

fly.

SkyBoy  (600) 

has  a great  deal  of  side area.  

Coupled with the low  wing, about 10 degrees 

of right thrust is  required for  stable flight.   DO 

NOT  ATTEMPT  FLIGHT  WITHOUT  THE 

PROPER  AMOUNT OF  RIGHT THRUST!    I 

know,  it  looks  weird,  but  trust  me,  it’s 

necessary.

SkyBoy  (600)

  is  capable  of  all  sport  4-

channel  aerobatics  including  Snaps,  Cuban 

Eights,  Wing  Overs,  Loops,  Rolling  Turns, 

and Inverted Flight.

Have  fun  learning  the  in’s  and  outs  of 

SkyBoy  (600)’s

  in  flight  performance,  and 

feel  free  to  share  your  thoughts  and 

experiences with our staff.  We are committed 

to improving your  build and flying experience 

and  are  constantly  refining  our  processes, 

designs,  and  manuals  to  reflect  customer 

feedback.  You may correspond with Stevens 

AeroModel  staff  using  any  of  the  following 

methods:

E-Mail -

 

[email protected]

 

RCGroups.com -

 Forum Build Threads.

Facebook.com -

 Search for Stevens AeroModel.

Phone -

 719-387-4187 M-F 10A-5P MST

SkyBoy 600 © 2010 Stevens AeroModel all rights reserved. 

Page 55 of 55

Содержание SkyBoy 600
























































Отзывы: