Steelcase 9 Series Скачать руководство пользователя | Manualshive

Страница: 14 / 18

background image

Page 14 of 18

939564905 Rev E

®

Attaching Wire Manager & End Caps (continued)

Remove the release liner from the dual lock
tape on the interior of the end caps.

Align end caps with the wire manager and install on the underside of the worksurface
around the outer edges of the lifting columns and mounting brackets. Press down at
the locations shown to bond the dual lock tape to the underside of the worksurface.

Non-Handed End Caps

A

C

B

TIGHT FIT, NO GAP

RELEASE LINER

14.

11.

19

14.

11.

20

«
...
12
13
14
15
16
...
»

Содержание 9 Series



















Отзывы:

Нет отзывов

Похожие инструкции для 9 Series

Бренд: keilhauer Страницы: 8

Бренд: UltraHD Страницы: 13

Бренд: Backyard Discovery Страницы: 32

Бренд: Happybeds Страницы: 5

Бренд: feather&black Страницы: 4

Бренд: EAST COAST Страницы: 12

Бренд: EAST COAST Страницы: 5

Бренд: EAST COAST Страницы: 10

Toronto Hall Table 2 Drawer

Бренд: fantastic furniture Страницы: 7

Бренд: fantastic furniture Страницы: 12

Бренд: fantastic furniture Страницы: 12

Бренд: fantastic furniture Страницы: 9

Бренд: fantastic furniture Страницы: 12

Бренд: MAJA Möbel Страницы: 8

Бренд: Gautier Страницы: 8

Бренд: Mayline Страницы: 4

Panacea Two-Sided Staircase

Бренд: Direct Supply Страницы: 2

Бренд: Walker Edison Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды