background image

 

7

Apart from this the controller allows for registrating the calorimetry fed into the service water storage basin by an 
additional volume flow dispenser and the temperatures in the solar forward and backward movement. The volume 
flow dispenser is a traditional water meter with pulse output point. It is important that the volume flow dispenser 
resists the higher temperatures within the solar circuit. This is the reason why you should not use cold water but warm 
or hot water meters sold by authorized dealers. 

 

3.2 Regulation 

function

 

Function overview 

Š

 "ON" and "OFF function" of the temp. difference regulation  

   (menu 

"On-temperature difference"

 = ON-Tdiff; menu 

"Off-temperature difference"

 = OFF-TDiff) 

Š

 menu 

"speed control" 

of the solar circulation pump 

Š

 

"storage tank temperature limitation"

 (menu 

"storage temp. limitation"

Š

 

"collector temperature limitation"

 (menu 

"collector temp. limitation"

Š

 Thermostat functions 

(due to software lock only one function to be selected)

 

 

y

 menu 

"storage tank cooling"

 

 

y

 

temperature

 

and time-linked

 

"heating system" 

(menu 

"heating system"

 

y

 

temperature

 

and time-linked "circulation control"

 (menu 

"temp.-linked circulat. contr."

, menu 

"time-linked  

 

  circulat. contr."

Š

 menu 

"antifreezing protection"

 

 

Š

 

"Manual operation"

 of the switch outputs (menu 

"MAN.OPERATION" 

 

3.2.1 

"On-temperature difference"

 and 

"Off-temperature difference"

 function of the temperature 

difference regulation (Appendix 10, illustration A) 

 

The solar circulation pump P1 is switched on by a temp. difference function. As soon 
as the collector temp T1 is a certain temperature difference (to be adjusted within 
the menu parameter "On-temperature difference"

 

higher than the sensor`s "storage 

tank bottom" T2 temp. the circulation pump will be switched on. 
In order to avoid a permanent ON and OFF of the solar circulation pump it only 
switches off automatically after falling below an adjusted temperature difference (to 
be configurated within the menu parameter "Off-temperature difference"). 
Example: 
The parameter value of the switch-on temperature difference is 8 Celvin, the 
parameter value of the switch-off temp. is 4 Celvin. On the point of measurement at 
the bottom of the storage tank (T2) 20°C are registered, i. e. in this case the solar 
circulation pump will be switched on at a collector temp. of 28°C and will be 
switched off at a collector temp of 24°C.  
 

IMPORTANT: 

The preset values of the switch-on (8 Celvin) and switch-off (4 Celvin) temperature difference have been proven 
standard configuration for years. Changing these values is thus only necessary in exceptionate situations, e. g. long 
pipeline distances. Switch-on and switch-off temperature differences are interlocked. Both values can be adjusted to a 
maximum of 2 Celvin against each other so that misconfiguration are avoided. 

 
 

3.2.2 

"speed control"

 of the solar circulation pump (Appendix 10, Illustration B) 

The controller has an electronic relay for the regulation of a circulation pump´s speed (P1) within the solar circuit. By 
regulation this speed the temperature difference between collector and storage tank is to be kept on a constant level. 
When using solar circulation pumps with changeable cycle speed stages the highest stage (in most cases stage 3) 
should be adjusted. This adjustment is done directly by moving the pump speed switch. The speed regulation 
automatically adjusts the necessary performance.  
The regulating performance of the speed control corresponds to a "PI" controller (proportional integral controller). The 
"P" part serves for a fast stabilisation of the regulation process and "I" part serves for a fast achievement of the preset 
set point. This controller is – due to its precise adjustment – extraordinarily rugged and it is not necessary for the user 
to conduct any detailed configuration. 
Nevertheless, you have the possibility to switch off the speed control within the menu functions “speed control”. Then 
the controller works just as a traditional temp. difference controller and takes care that the circulation pump delivers a 
constant volume flow (if the switch-on conditions are fulfilled). 
 
 
 
 

Содержание Suntana


























Отзывы: