background image

3

718.573 | 11.27

1.  Safety instructions and liability disclaimer

1.1. The safety instructions are marked as follows

In this manual, safety instructions for personal protection are marked with this 

symbol.
The relevant operational safety notes of the system and regulator are marked 

in bold.

1.2. General Safety Instructions

Observe the following while installing the regulator and handling the battery:
Danger of explosion due to improper handling of batteries! Corrosive hazard by 

leaking battery acid! 
Keep children away from batteries and acid! Smoking, fire and naked lights are 

prohibited when handling batteries. Prevent sparking and wear eye protection 

gear during installation. Observe and follow the handling instructions in the 

user manual and on the battery.
Solar modules generate power from light incidence. Even by low light incidence 

solar modules carry the full voltage. Therefore, work cautiously and avoid spark-

ing during all work. Observe the corresponding safety precautions. 
During installation and electrical installation, the photovoltaic system’s DC 

circuit may carry twice its system voltage value (in the 12 V system up to 24 V, 

24 V system up to 48 V).
Use only well-isolated tools!
Do not use any technical measuring equipment that you know is damaged or 

defective!
When installing the power line ensure that no fire safety measures are dam-

aged. The regulator may not be installed and operated in moist rooms (e.g. rest 

rooms), or rooms, in which easily flammable gasoline mixtures may be present, 

such as by gas bottles, paint, lacquer, solvents etc. Do not store any of the men-

tioned mixtures in the room, in which the solar regulator is installed!
If the regulator is operated in a manner not specified by the manufacturer, the 

regulator’s constructive protective measures can deteriorate.
The factory signs and marking may not be modified, removed or made unrecog-

nizable. All work must be performed in conformity with the national electrical 

specifications and related local regulations! 
When installing the regulator in foreign countries, information concerning regu-

lations and protective measures must be obtained from the relevant institutions 

/ authorities.
Do not begin the installation until you are sure that you have technically understood 

the manual and perform the work only in the order provided in this manual!
The manual must be available during all work performed on the system, third 

parties included.

Содержание PR 2020 IP65

























Отзывы: