Steca PR 2020 IP65 Скачать руководство пользователя страница 15

15

718.573 | 11.27

8.  Error Messages  

Caution! Please do not open the regulator or attempt to replace 

components when troubleshooting. Improper maintenance can be 

hazardous to the user and the system.

If the regulator detects errors or unauthorized operating states, it flashes error codes 

on the display. Error codes can generally be differentiated, whether there is a temporary 

malfunction, e.g. regulator overload or a more serious system error that can be remedied 

by appropriate external measures. 
Since not all errors can be simultaneously displayed, the error with the highest error 

number (priority) is displayed. If several errors are present, the second error code is 

displayed after remedying the more significant error.
The following meaning is assigned to the different error codes:

Display

Meaning

Cause / Remedy

Communication er-

ror with the internal 

memory (EEPROM).

Disconnect consumer, solar  module 

and battery. Reinstall the device. If the 

error reoccurs, please contact your 

specialized dealer.

Communication error on 

the  external bus (6-pole 

edge    connector).

Check the 6-pole plug-in connection 

on the edge connector, power supply 

and function of the external extension. 

If the error reoccurs, please contact 

your specialized dealer.

Short-circuit at the exter-

nal temperature sensor.

Check the contact of the 2-pole edge 

connector, remove short-circuit. Check 

sensor.

Excessive temperature 

regulator turned off the 

consumer due to internal 

over heating.

Let regulator cool. Check the cause for 

overheating (installation site, other 

heat sources). Possible reduce charge 

or load current. Ensure the regulator 

has proper ventilation.

Battery voltage too low. 
Voltage <10.5 V or 

<21.0 V

Check installation. Check battery volt-

age, possibly recharge battery manu-

ally. Consumer connected directly to 

the battery can deep-discharge the 

battery.

Battery voltage too high.
Voltage >15.5 V or  

>31 V.

Check installation. Check battery volt-

age, possibly check additional charge 

sources. 

Содержание PR 2020 IP65

























Отзывы: