stayer EPG 800, Руководство по эксплуатации

Страница: 20 / 48

gb
/
20
/
This manual is consistent with the date of manufacture of
your machina, you will find information on the technical
data of the machi ne acquired manual check for updates
of our machines in the web-page:
www.grupostayer.com
Thank you very much for acquiring a STAYER
product!
We congratulate you for having elected a STAYER
Electric spray gun. We are sure that this modern tool will
fully comply with your expectations.
The power tool is intended for atomising solvent-
based and water-dilutable paints, finishes, primers,
clear finishes, automotive finishes, staining sealers,
wood sealer preservatives, plant protectives, oil and
disinfection agents.
To ensure proper operation and performance of your new
EPG300 / EPG800, and to safeguard its own security, it is
imperative that you read this instruction manual carefully
befare using the tool
Be especially .careful to observe all safety precautions!
Failure to observe these precautions may result in serious
injury or even death!
Packaging
STAYER paint your gun will be delivered in a protective
cardboard box to prevent damage during transport.
Cardboard is a basic eaw material and, therefore, reusable
and suitable for recycling (waste paper recycling).
Specific safety instructions
Read all safety warnings, instructions including material.
Workplace safety.
-
Keep area well lit and free of paint or solvent
containers, regs, and other flammable materials.
Spontaneous combustion may occur. Fire extinguisher
equipments shall be present and working at all times.
- Provide for good ventilation in the spraying area
and for sufficient fresh air in the complete room.
Evaporating inflammable solvents create an explosive
environment.
- Do not use materials with a flashpoint below 21 ºC for
spraying and cleaning. Use water-based materials,
non-volatile hydrocarbons or similar materials . Fast
evaporating solvents create an explosive environment.
- Do not spray in the vicininty of ignition sources,
such as static electricity sparks, open flames, pilot
lights, hot objects, engines/motors, cigarettes and
sparks from plugging in or unplugging power cords
or operating switches. Such spark sources can ignite
the spraying vicinity/environment.
-
Do not spray any liquid of unknown hazard potential.
Unknown materials can create hazardous conditions.
Personal safety
- Wear additional protective equipment such as
appropriate protective gloves and protective
masks or respirators when spraying or handling
chemicals.
Wearing protective equipment for the
appropriate conditions reduces the exposure to
hazardous substances.
- Never point the spray jet against yourself, towards
other persons or animals. Keep your hands and
other body parts away from the spray jet. lf the
spray jet should penetrate the skin, seek medical
attention immediately from a doctor. The material
being sprayed can even penetrate the skin through a
glove and be injected into your body.
- Do not treat injection as a simple cut. Highpressure
spray is able to inject toxins into the body and cause
serious bodily injury. In the event that injection occurs,
seek medical attention immediately.
- Be aware of possible hazards from the spray
material. Ob serve the information on drums/
tanks/tins as well as manufacturar information of
the spray material, including the request to wear
personal protective equipment. The manufacturer’s
instructions are to be observed in arder to reduce the
risk of fire as well as injuries caused through toxins,
carcinogens, etc.
Use and Handling of the PowerTool
- Use only nozzles/nozzle inserts specified by the
manufacturar. Never spray without the nozzle
protection mounted. Use of a special nozzle insert
with the corresponding nozzle protection reduces the
probability that a high-pressure jet penetrates the skin
and injects toxins into the body.
- Exercise caution when cleaning and changing nozzle
inserts. lf the nozzle insert should become clogged
during spraying, follow the manufacturer’s instructions
for switching off the system and relieving the pressure
before removing the nozzle. Fluids under high pressure
can penetrate the skin, inject toxins into the body and
lead to serious injury.
- Keep the plug of the mains cord and the trigger switch
of the spray gun clear of paint and other fluids. Never
hold the cord by its connectors to support it. Failure to
fallow the instruction can lead to electric shock.
lnstructions for use
Placement Tool
Read all safety warnings and all instructions. Failure
to fallow the warnings and instructions may result in
electric shock, tire and/or serious injury.
To get started, place the machines in a clean and stable,
begin by preparing the material to be sprayed, taking
into account tilis point, because if not well prepared m
hand the material, the machine will not work in conditions
optimal.
Assembly (Fig.1)
Before any work on the machine itself, pull the mains
plug.
Mounting the Spray Gun and the Electrical Unit.