stayer EPG 800, Руководство по эксплуатации

Страница: 21 / 48

/
21
/
es
gb
it
fr
p
pl
Connecting the Electrical Unit with the Spray Gun.
- lnsert the spray gun 9 onto the electrical unit 1 until it
can be heard to engage.
- lt should be noted that SD 4 moths faund on the
sides of the gun should be open positioned. Then
return to the closed position moths and make sure
that the spray gun is secure.
Removing the Electrical Unit
-
Turn the two red SDS selease buttons open 4 and
pull the spray gun 9 out of the electrical unit.
EPG 800
- Insert the air tube 23 through the nozzle 26 in the
body of the gun 1. Insert the air tube in the trolley
through the nozzle 24.
When inserting the air tube 23, turn the nozzle
clockwise so that the tube is properly seated and
engaged on the gun and trolley.
Electrical connection
- Plug the mains plug into a socket outlet.
- Grasp the power tool and point it at the spray
surface. The power tool is equipped with a two-step
trigger switch 16. The first step starts the turbine.
The second step transports the spraying material.
- Pull the trigger switch 16 until
spraying material starts to come out.
Switching Off - Release the trigger switch 16.
- Pull the mains plug from the socket outlet.
lllustrated description
The fan motor causes a fiow of air fiowing through the air
hose 23 to the spray gun. The air flow is atomized coating
material on the nozzle 20 and pressurized vessel 11. This
pressure forces the coatíng materíaí through the riser
pipe to the nozzle 20. The adjustment of air and pressure
can be adjusted progressively. (Fig. 4-5-6).
1 Electrical unit
2
Cable clamp
3 Air filter cover
4 SDS release button*
5 Mains cable
6
Base/foot*
7 Hooks far air-filter cover
8 Air filter
9 Spray gun
10
Suction tube with container seal
11 Container far spray material, 800 ml
12 Vent cover
13 Oiffuser
14
Clamp nut
15 Thumbwheel far spraying capacity
16 Trigger switch
17 Air outlet
18
Venting valve*
19 Membrane*
20 Nozzle*
21 Nozzle seal*
22
Measuring cup
23
Air Hose*
24 Air intake
25 Troley*
26 0ut of air
27
Cleaning needle*
* The accessories illustrated or described are not attached
to the material standard. The full range of accessories
can be found in our accessories program.
Operating instructions
Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified
on the nameplate of the machine.Power tools
marked with 230 V can also be operated with 220 V.
Pay attention that the power tool cannot draw in dust
or other contamination during operation.
Placement and testing (Fig.2-3)
Observe the wind direction when operating the power
tool outdoors.
- Firstly, carry out a test-spray run and adjust the spray
pattern and the spray material quantity according to
the spray material. (For adjustments, see the following
sections)
- Make sure to hold the spray gun vertical to the spray
object at a uniform clearance between 5-15 cm.
- Begin the spraying procedure outside the target area.
- Move the spray gun evenly cross-wise or
upand-down, depending on the spray pattern
setting. An even surface quality is achieved when the
paths overlap by 4 - 5 cm.
- Avoid interruptions inside the target area.
An even movement of the spray gun results in an even
surface quality. Non-uniform clearance and spray angle
lead to heavy formation of paint mist and thus to an
uneven surface.
- End the spraying procedure outside the target area.
Never spray the container completely empty. When the
suction tube no longar immerses in the spray material, the
spray jet will break off, resulting in a non-uniform surface.
When coating material builds up on the nozzle and air
cap, clean both parts with the corresponding solvent.
Only place down the power tool on a level and clean
surface so that it can not tip over.
Adjusting the Spray Pattern (fig. 4-5-6)
Never actuate the trigger switch 16 while adjusting
the air cap 13-14.
- Loasen the union nut 14.
- Turn the air cap 13 to the requested position.
- Firmly retighten the union nut 14.