background image

Technical Primer - Aurora

1

Copyright and Disclaimer

1.1

Disclaimer

• This document has been subject to rigorous technical review before being published. It will

subsequently be revised at regular intervals. Any modifications or amendments will be included

in the future. Content of this document is compiled for information purposes only.

• Although StarCharge has put its best efforts to keep the document as precise and up-to-date,

StarCharge shall not assume any liability for defects and damage which may result from the

use of information contained herein.

• In no event will StarCharge be liable for direct, indirect, special, or consequential damages

(incl. loss of profits) resulting from any errors or omissions in this manual. All obligations of

StarCharge are stated in the relevant contractual agreements. StarCharge reserves the right

to revise this document from time to time.

• Any deviation to the products including, but not limited to, customer-specific modifications

(like placing stickers, SIM cards or the usage of different colours), hereafter referred to as

’Cus-

tomization’

, can alter the final product’s user experience, appearance, quality and/or lifespan.

• StarCharge is not liable for any damage to or caused by the product Customization is the main

cause.

• Contact your dealer for more information on Customization versus the default product.

1.2

Copyright

All rights reserved. The disclosure, duplication, distribution and editing of this document, or

utilization and communication of the content are not permitted, unless authorized in writing. All

rights, including rights created by patent grant or registration of a utility model or a design, are

reserved.

1.3

Warranty

StarCharge shall not be liable in any way for damage. All warranties on both the product and

accessories shall become void under the following circumstances:

• The ambient temperatures during are below -30

C or above 50

C.

• The products have been installed wrong, subject to misuse or badly maintained.

• The instructions in manuals associated with operation and maintenance for the products(or

parts provided at the time of purchase) of the device have not complied.

• The products are used in the vicinity of explosive, highly flammable substances or in or near

water.

• There is a failure of the distribution network.

Attention

Extensive safety information is available in the relevant sections of this document. The safety instruc-

tions are intended to ensure proper practical usage. If the user does not comply with these safety

regulations and instructions, the user may expose herself/himself to the risk of electric shock, fire

and/or severe injuries.

Wanbang Digital Energy Co.Ltd

5

Содержание Aurora 11kW































Отзывы: