Star Microwave SM Cirius AO Скачать руководство пользователя

Страница: 20 / 85

2 BEFORE STARTING THE INSTALLATION

2.1 SITE PREREQUISITES

Introduction

This section describes all the prerequisites that must be considered prior to installing the
equipment.

Site Survey

Site survey should be done before start the installation taken in consideration the following:

Premises information



Site details (address, contact persons, GPS and/or map co-ordinates, etc.)



Site access and storage information (means of transport, equipment storage and lifting

information, etc.)



Site location maps

Network planning



Geographical positions of the site



LOS between the sites



Rain zone



Polarization of the antennas



Height of all buildings at the installation premises



Rooftop information (height, status, access, dimensions, layout, etc.)



Information about pre-existing indoor/ outdoor equipment



Available mounting space (on the buildings’ roofs) to reserve for the installation of the
outdoor equipment

Site-specific information



Mechanical specifications of masts/ towers (type, dimensions/ diameter, material, exterior

finishing, etc.)



Location of appropriate grounding points (bar or terminals)



Location of appropriate power supply distribution points



Location of cable conduits available for routing the cables



Location of the network port distributors



Total length of the cables required

Содержание SM Cirius AO






















































































Результаты поиска

Содержание SM Cirius AO

Отзывы:

Похожие инструкции для SM Cirius AO

Бренды по названию

Популярные бренды

Star Microwave SM Cirius AO, Руководство по установке

Результаты поиска

Содержание SM Cirius AO

Отзывы:

Похожие инструкции для SM Cirius AO

Бренды по названию

Популярные бренды