Stanley 204143 Скачать руководство пользователя

Страница: 3 / 48

iQ Control Box

10.18.2019

1.800.7.ACCESS • www.stanleyaccess.com • Document # 204143 REV 5 3

Cop

ight 2019, S

tanley Ac

cess T

echnologies, LL

C. All rights r

ved. R

epr

oduction

in whole or in p

t without the expr

ess wr

itt

en permission o

f S

tanley is pr

ohibit

ed.

2S Operation

ON =

push switch to open, push switch to close;

OFF =

2S mode disabled.

Close Position Tolerance

: Distance from full close that the door transitions from close check to full closed. This parameter

is used when the door can’t get closed and to eliminate recycles caused by obstructions. This sets the position where the

controller interprets the door as fully closed.

Close Obstruction Time

: The amount of time in increments of 0.1 seconds the spring applies force when almost stopped

or stopped when the controller indicates a state of

. Before increasing this parameter, check for mechanical issues.

Fire Alarm Mode

0 = OFF

Keeps the Fire Alarm Mode OFF.

1 = OPEN

If not already Fully Open, the controller will ignore sensors and open the door slowly. If the door was

previously obstructed, it will remain at the partially opened position. The controller will cause the door to remain

open/partially opened for the duration of the Fire Alarm activation.

2 = CLOSE

Ignore Sensors and Hold Open Switch Mode

: If the door is Fully Closed, the controller will ignore

activation sensors. If not already Fully Closed, the controller will ignore sensors, Hold Open, and close the door.

If the door is obstructed, it will not recycle and leave the motor drive in “freewheel”.

3 = OPEN WITH RETRY

If not already Fully Open, the controller will ignore sensors and open the door slowly.

If the door becomes obstructed, it will pause for 0.5 second and reattempt opening. The controller will cause the

door to remain open/attempt opening for the duration of the Fire Alarm Activation.

4 = CLOSE

Ignore Hold Open Function Switch Mode

If the

door is Fully Closed, the controller will ignore

activation sensors. If not already Fully Closed, the controller will ignore the Hold Open but observe sensors normally

if in automatic or one way. If the door is obstructed, it will not recycle and leave the motor drive in “freewheel”.

Hold Beam Type

: Selects the hold beam type to be used for monitored or non-monitored applications.

Monitored Hold Beams: Photobeam Pro or Optex OS12CT. Refer to wiring diagrams per application.

Hold Open Delay

: Amount of time the door stays open after all sensors have cleared.

I/O Configuration

: Allows Motor 2 Power Close Relay feedback to be used instead of functions normally used with the

selected input:

0 = Default
1 = TB5-7

: Motor 1 Relay Feedback, TB3-9 Motor 2 Relay Feedback. OPEN: If not already Fully Open, the

controller will ignore sensors and open the door slowly. If the door was previously obstructed, it will remain at the

partially opened position. The controller will cause the door to remain open/partially opened for the duration of

the Fire Alarm activation.

2 = TB2-5

: Motor 1 Relay Feedback, TB3-9 = Motor 2 Relay Feedback. If the door is Fully Closed, the controller will

ignore activation sensors. If not already Fully Closed, the controller will ignore sensors, Hold Open, and close the

door. If the door is obstructed, it will not recycle and leave the motor drive in “freewheel”.

Lock Delay

: This allows the lock to mechanically unlock before door motion. Lock Delay only occurs when the door is full

closed (when the control displays

). When the door is activated while the door is open, no Lock Delay occurs. Lock Delay

will always occur if a door position switch is active. Value is in 0.1 second increments.

Lock Logic

: Select to choose desired lock logic:

0 = Fail Safe

: U

nlocked when power is removed.

1 = Fail Secure

: Locked when power is removed.

Lock Release Time

: The amount of time (in seconds) that the door will press closed before going open when the lock

needs to release at the closed position. The value of zero disables the lock release.

Lock Release Torque

: The torque used in the lock release state. This parameter sets the maximum current available

to the motor which is directly proportional to the door force.

Magic Touch Engagement

: Determines how smooth the door is to push after a Magic Touch activation.

Magic Touch Hold Open Time

: Delay that the door stays open after all sensors have cleared after a Magic Touch operation.

Parameter is in seconds, with increments of 0.1 seconds.

Magic Touch Sensitivity

: Sets the threshold for manual activation. Setting of 1 is most sensitive. This setting is raised

if false activations are seen.

Manual Mode Sensor Override

: When set to

the door sensors on the approach side will only be activated when a push

plate, Magic Touch, or other Knowing Act activation signal is used.

= NOT SELECTABLE BY KEY PAD/PUSH BUTTONS

Features and Functions

Содержание 204143

















































Результаты поиска

Содержание 204143

Отзывы:

Похожие инструкции для 204143

Бренды по названию

Популярные бренды

Stanley 204143, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 204143

Отзывы:

Похожие инструкции для 204143

Бренды по названию

Популярные бренды