manualshive.com logo in svg

Stanley 204143, Инструкция по установке и эксплуатации

Поделиться
Скачать
Stanley 204143 Скачать руководство пользователя страница 6

iQ Control Box

6     Document # 204143  REV 5 •  www.stanleyaccess.com • 1.800.7.ACCESS 

Cop

yr

ight 2019, S

tanley Ac

cess T

echnologies, LL

C. All rights r

es

er

ved. R

epr

oduction 

 

in whole or in p

ar

t without the expr

ess wr

itt

en permission o

f S

tanley is pr

ohibit

ed.

10.18.2019

WIRING INSTRUCTIONS

Evaluate Power Requirements

EVALUATE door system power requirements as follows:

•  ENSURE power source is a dedicated 115 VAC, 50/60 Hz source with 20A circuit rating per two controllers.
•  ENSURE power source is not shared with other equipment, i.e., cash registers, EAS systems, or other 

 

electromagnetic interference generators.

Connecting Main Power Wiring

Warning

:

 To prevent injury to personnel, incoming electrical power to header must be de-energized before 

 

      connecting control box electrical harness to electrical service.

•  DE-ENERGIZE incoming electrical power to header.
•  Refer to Attachments 2, 3, and 4, and using the wire nut provided, CONNECT ground wire assembly (P/N 

711527) to electrical service ground wire.

•  In a concealed location inside the header (not visible from the exterior of the header), DRILL a hole for a 

 

No. 8 screw.

•  INSTALL ground wire ring terminal and star washer onto the No. 8 screw provided, and FASTEN screw, star 

washer, and ground wire to header.

•  In a concealed location inside the header, DRILL a second hole for a No. 8 screw.
•  INSTALL power line harness 412544 ring terminal and star washer onto the No. 8 screw provided, and FASTEN 

screw, star washer, and ground wire to header.

•  Using the wire nuts provided, CONNECT power line harness 412544 to electrical service as follows:

•  CONNECT power pigtail assembly black wire to black (line) service wire.
•  CONNECT power pigtail assembly white wire to white (neutral) service wire. 

Connecting Breakout Status Signal Wiring (Magic-Swing Operators)

Warning

: To prevent injury to personnel and damage to equipment, control box power must be de-energized 

before connecting breakout status signal wiring.

Caution

: If the motor is running and the breakout status switch is 

not

 connected, arcing across the breakout 

switch contacts can occur. This will result in damage to the breakout switch. To prevent damage from switch 

contact arcing, the breakout status switch must 

always

 be connected.

NOTES

: 

The breakout status switch must be used in all applications where there is no positive door stop in the 

 

breakout direction.
The auxiliary switch is the breakout status signal switch. The auxiliary switch was formerly the open check switch 

on the operator switch plate (top cam).

•  Refer to Attachment 1, and CONNECT breakout status wiring.
•  REMOVE quick-connect terminal (brown wire) from the normally open terminal of the auxiliary switch 

(formerly open check switch), and INSTALL onto normally closed terminal. 

2

Continued Next Page

Содержание 204143

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды