Standard Change-Makers Guardian BE страница 45 Скачать руководство пользователя | Manualshive

Страница: 45 / 99

background image

45

5.8.4.10

Troubleshooting

When connected to the WashGear card system the WashGear version will appear in the
“CONFIGURATION REPORT”. If communication is lost the version will be replaced with “not
connected”.

After initializing, the GXP will beep twice indicating that auto addressing is done. A single beep will
occur when a connection has been made to the WashGear card system.

Make sure the WashGear is selected under “CREDIT SETTINGS” and that a location id has been
entered in “OTHER SETTINGS”.

On advance replacements for the EFIII board, make sure the proper software version and board
revision is used.

What do the lights on the ethernet connector mean?

The left LED indicates a connection. It requires a loop back from the other device. In other words for
the light to be on it has to be connected at both ends.

The right LED indicates data flow. This can be just data out with no response.

1. WashGear is not selected and the cable is not connected.

No LEDs on

2. WashGear is not selected but the cable is connected.

Left LED on steady green

    When power is cycled or the Guardian is reset.
        Left LED goes off while right led blinks orange
        Then left LED is on steady green

3. WashGear is selected, the cable connected and after WashGear connection.

Left LED on
Right LED blinks green occasionally

Note:
This is the same if the WashGear application goes away.

4. WashGear selected, the cable is disconnected after WashGear connection.

Left LED off
Right LED blinks orange

«
...
43
44
45
46
47
...
»

Содержание Guardian BE




































































































Отзывы:

Нет отзывов

Похожие инструкции для Guardian BE

Бренд: Gasboy Страницы: 82

Бренд: Quooker Страницы: 8

Бренд: H2O International Страницы: 20

Multidrop Combi nL

Бренд: Thermo Scientific Страницы: 106

Бренд: Electrolux Страницы: 9

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 16

Бренд: Electrolux Страницы: 32

Бренд: Grindmaster Страницы: 6

Бренд: Igloo Страницы: 1

Бренд: Perrin & Rowe Страницы: 2

BOTTLE-FREE WATER DISPENSER

Бренд: Permatech Страницы: 17

Бренд: American Changer Страницы: 35

Бренд: ultraMEDIC Страницы: 2

Бренд: Borg & Overstrom Страницы: 8

Бренд: Maxima Страницы: 12

Бренд: Bunn Страницы: 58

Бренд: Bunn Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды