Standard Change-Makers Guardian BE страница 10 Скачать руководство пользователя | Manualshive

Страница: 10 / 99

background image

10

2.1.2

Emptying The Coin Dispenser

The majority of coins in a dispenser can be removed from the hopper using the

bulk dump

method.

Bulk dumping refers to the manual method of tilting the coin dispenser forward in order to empty
coins from a dispenser into a container. A few coins will remain in the dispense disk following a

bulk

dump;

these coins can be removed by performing an

electronic dump

.

CAUTION

As a safety precaution you should never place your fingers in or near the coin dispense chute or in
the coin storage area of the coin dispenser when power is applied to the dispenser.

Bulk Dump Method

Electronic Dumping Method

Electronic Dump

- The coin dispenser must first be in a “Sold Out” condition and not in error. This

condition occurs when the remaining coins are insufficient to complete a vend for a large
denomination bill. The yellow diagnostic LED will be blinking at a slow steady pace indicating a
Sold Out condition. To begin, turn the machine power off, then back on. Wait for the machines Out
Of Service lamp to change from the constant ON state to a BLINKING or OFF state. Make sure that
the dispenser is flashing a dispenser sold out code. If any other flash code is shown when pressing the
red

Push Button

it will reset the dispenser. You will have to power cycle the dispenser again. Next,

press and release the

Push Button

(see diagram below for location). The dispenser will begin

dispensing within 5 seconds. The coin dispenser will stop when all coins have been cleared. Note:

The Push Button must be pressed within 5 minutes of the time the power was turned off / on to
the machine.

2.1.3

Programming the Coin Dispenser

If for any reason it becomes necessary to change the denomination of the coin to be dispensed, you
must first contact a factory authorized service center to determine if the hopper can dispense the new
coin size (diameter & thickness).   If it can, then you need only to change the DIP switch setting on
the hopper dispenser board to program the hopper for the new coin value.  Once this setting has been
made, press the reset button to enter in that value.  The DIP switch located on the hopper control

Dump
Position

Coin Dispenser – Bulk Dump

Bulk dumping

is performed the same way for all

standard  capacity  (3200  quarters)  coin  dispensers.
Do not use the bulk dump method to empty a high
capacity  hopper  unless  it  has  only  30%  or  less  of
the coins  remaining.  Coin  dispensers  in  front  load
machines  tilt  forward,  and  dispensers  in  rear  load
machines  tilt  back.  Always  TURN  POWER  OFF
before bulk dumping a hopper for safety purposes.
To  tilt  the  coin  dispenser  pull  forward  at  the  top
edge  of  the  dispenser.  There  is  a  handle  in  the
middle of the opening to assist in bulk dumping.

«
...
8
9
10
11
12
...
»

Содержание Guardian BE




































































































Отзывы:

Нет отзывов

Похожие инструкции для Guardian BE

Бренд: lancer Страницы: 42

KEP AC-EBF-SND Series

Бренд: Franke Страницы: 34

Бренд: dymax Страницы: 20

Бренд: Tatung Страницы: 4

Бренд: Tatung Страницы: 8

Hyperchill HLS022

Бренд: Parker Hiross Страницы: 36

Бренд: H2O Страницы: 2

Бренд: Dreve Страницы: 88

Бренд: Igloo Страницы: 8

Бренд: Igloo Страницы: 9

Бренд: Bunn Страницы: 24

Бренд: TET Страницы: 14

Бренд: GEAppliances Страницы: 32

Бренд: Perlick Страницы: 12

Бренд: Tennant Страницы: 14

Бренд: Trixie Страницы: 2

Бренд: Hague Quality Water Страницы: 40

Бренд: Rainfresh Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды