SST Automation GS11-EI Скачать руководство пользователя страница 8

Страница: 8 / 51

User Manual

Embedded EtherNet/IP Module

GS11-EI

If this pin is pull down to low voltage before starting the module (by using a 1K

pull-down resistor), the module will start with default IP address (192.168.0.11), and

this mode is only used to update the firmware.

BAUD2

Set the UART baud rate (Input), see the following table.

BAUD1

BAUD0

/RESET

Reset signal (Input), Active low.

+3.3V

+3.3V DC power Supply

GND

GND power Supply

17 ~ 19

Reserved

/DATAEXCH

Data Exchange (Output), and need a 10K pull-up resistor on the user board.

Logic 1: The module is in non-data exchange state (such as start state, waiting for

initialization state, start the EtherNet/IP protocol stack, etc.)

Logic 0: The module is ready for data exchange.

2.4 UART Baud Rate

UART baud rate settings are as follows:

Index

BAUD2

BAUD1

BAUD0

Baud Rate

（

bps

）

2400

4800

9600

19200

38400

57600

115200

230400

Содержание GS11-EI




















































Результаты поиска

Содержание GS11-EI

Отзывы:

Похожие инструкции для GS11-EI

Бренды по названию

Популярные бренды

SST Automation GS11-EI, Руководство пользователя

Результаты поиска

Содержание GS11-EI

Отзывы:

Похожие инструкции для GS11-EI

Бренды по названию

Популярные бренды