SST Automation GS11-EI Скачать руководство пользователя страница 7

Страница: 7 / 51

User Manual

Embedded EtherNet/IP Module

GS11-EI

Pins

Signals

Descriptions

Pin 1

TXD+

Transmit Data+

Pin 2

TXD-

Transmit Data-

Pin 3

RXD+

Receive Data+

Pin 4

BID+

Bi-directional Data+

Pin 5

BID-

Bi-directional Data-

Pin 6

RXD-

Receive Data-

Pin 7

BID+

Bi-directional Data+

Pin 8

BID-

Bi-directional Data-

2.3.2 Host Interface

GS11-EI has a 20-pin socket connector (needle-type), including power, UART and GPIO. The pin position

and definition are as follows:

Pins

Signals

Description

1 ~ 6

Reserved

RXD

UART Receive (Input), connect with TXD of host processor or MCU

TXD

UART Transmit (Output), connect with RXD of host processor or MCU

GPIO

Reserved

/RUN

The status of GS11-EI (Output), and need a 10K pull-up resistor on user board.

Logic 1: The GS11-EI module is in starting.

Logic 0: The module’s start has been completed. (Include waiting for initialization

state, start the EtherNet/IP protocol stack and data exchange state, etc.)

Содержание GS11-EI




















































Результаты поиска

Содержание GS11-EI

Отзывы:

Похожие инструкции для GS11-EI

Бренды по названию

Популярные бренды

SST Automation GS11-EI, Руководство пользователя

Результаты поиска

Содержание GS11-EI

Отзывы:

Похожие инструкции для GS11-EI

Бренды по названию

Популярные бренды