SRAM ROAM 50 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 40

background image

22

ROAM 50 Front Hub Bearing Replacement

Turn the wheel over so that the Large Diameter Hub Tool and

installed bearing are on the work bench. Install a new bearing onto

the axle.

Install the other Large Diameter Hub Tool over the axle and into

the hub. Strike the tool with a soft face mallet until the bearing is

firmly seated into the bearing pocket. Periodically check bearing

alignment in the hub.

Check the axle for play by pushing and pulling it in the hub. If any

play is detected, repeat steps

12-16

.

Apply a light layer of grease to each bearing face. Use a rag or

paper towel to remove any grease from the ends of the axle.

15

16

Large Diameter Hub Tool

17

18

«
...
20
21
22
23
24
...
»

Содержание ROAM 50









































Отзывы:

Нет отзывов

Похожие инструкции для ROAM 50

Бренд: Babboe Страницы: 132

Бренд: Felt Страницы: 22

Бренд: Felt Страницы: 29

Бренд: Razor Страницы: 36

Бренд: Razor Страницы: 19

Бренд: Öhlins Страницы: 9

Бренд: TRIOBIKE Страницы: 12

Бренд: DOCYKE Страницы: 41

Бренд: Green Light Cycle Страницы: 24

Бренд: Huffy Страницы: 36

Бренд: SYXmoto Страницы: 20

CHINOOK RAIN COVER

Бренд: Chariot Страницы: 4

Evolution Smart

Бренд: NiteRider Страницы: 16

Бренд: Yerf-Dog Страницы: 7

Бренд: Yeti Cycles Страницы: 18

SL F NANO STVZO

Бренд: Lupine Страницы: 11

Бренд: Lupine Страницы: 29

Бренд: Richelieu Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды