SportsPlay Quick Ship 3 Modified Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 140

background image

VALUE SERIES

INSTALLATION APPENDIX

4/2/10 M-C_APPENDIX.V1.0410

2

FINAL INSTALLATION STEPS

__1. Once the entire playground has been assembled level and
square each post, deck and component.

__2. Tighten all hardware.

__3. Starting at the center of the structure and working out
towards the perimeter of the structure, pour concrete into
footing holes. Leave 2” from the top of the hole to the top of
the concrete to allow for backfill. Slope concrete down and
away from post to water from seeping between the post and the
concrete. Refer to the footing sections in the individual
component instructions for a cutaway drawing.

__4. Clean off any concrete that may have splashed onto
equipment before it dries.

__5. After the concrete has set for a minimum of 48 hours
(refer to manufacturers instructions for proper cure time) you
should backfill the holes. Also, remove any concrete that is not
in the holes so they don’t become a hazard for children.

__6. Install labels as instructed on the next page.

__7. Install Surfacing. A protective surfacing material is
required under and around all play equipment within the use
zone. If using loose fill surfacing, we recommend a depth of
12” for the entire use zone.

Loose fill surfacing material must be maintained at the required
depth within the use zone. Loose fill material must be replaced
or added as necessary to maintain its resilient properties.

«
...
104
105
106
107
108
...
»

Содержание Quick Ship 3 Modified













































































































































Отзывы:

Нет отзывов

Похожие инструкции для Quick Ship 3 Modified

Бренд: KAPSCH Страницы: 57

Бренд: MacDon Страницы: 272

Бренд: MacDon Страницы: 70

Бренд: EAW Страницы: 2

Бренд: U-Line Страницы: 9

Green Machine H-3518

Бренд: U-Line Страницы: 3

Бренд: Vaniman Страницы: 3

Бренд: Lalizas Страницы: 12

UG 2200 Special

Бренд: Amazone Страницы: 252

Бренд: Yardbird Страницы: 12

ikon profile ww

Бренд: ADJ Страницы: 15

Multi Use Tester III

Бренд: Fuso Страницы: 92

Hart Scientific 9101

Бренд: Fluke Страницы: 17

6X6 Chicken Coop & Run

Бренд: E-Z FRAME Страницы: 8

Бренд: Kellfri Страницы: 16

Batt-O-Meter KS700-0658

Бренд: Keith McMillen Instruments Страницы: 4

Бренд: JB Systems Страницы: 16

Бренд: SET Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды