SportsPlay Quick Ship 3 Modified Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 140

background image

March 10, 2014

8

922-126-3 (3’) TRIPLE RAIL SLIDE

INSTALLATION INSTRUCTION

INSTALLATION STEPS CONTINUED

__9.

Insert the 3/8 x 3/8 socket set screws

(#10) into the threaded

hole on the bottom side of the four-hole attachment brackets (#4)
and tighten (Detail C on page 7).

__10.

Level and square the slide

making sure to keep 11” of

spacing from the slide bed to the top of the safety surfacing.

__11. Once slide is in position and you have verified its square and
level you may

tighten the bolts connecting the slide to the deck.

__12.

Inspect the components

for sharp edges and if necessary file

them down and apply touch up paint.

__13. Once the entire playground has been installed and you have
verified that the entire playground is level you can

add the

concrete to the footing holes.

Be sure to use concrete with a

minimum 2,500 psi and mix the concrete per the manufacturer’s
directions before you pour it into the footing hole. Once the footing
has been filled with concrete you should rope of the area for a
minimum of 48 hours to allow the concrete set properly.

__14.

Once the concrete has set,

back fill dirt over the footing

holes: inspect the area and components for tools, hazardous debris
and sharp edges. Verify all components are installed and all
hardware is tight and then install the safety surfacing.

__15.

Install labeling

as instructed in the appendix of the

instruction manual.

INSTALLATION STEPS CONTINUED

TIP: It’s easier to install the self tapping screws if you pre drill
the holes in the post with a #7 drill bit by marking the hole
locations with a dry erase marker after you have put the guard
wall into position.

«
...
61
62
63
64
65
...
»

Содержание Quick Ship 3 Modified













































































































































Отзывы:

Нет отзывов

Похожие инструкции для Quick Ship 3 Modified

Бренд: Keller Страницы: 12

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 4

Бренд: Hands Free Farm Страницы: 24

Бренд: Rapid Shape Страницы: 12

Бренд: Wiltron Страницы: 13

Бренд: airwave Страницы: 32

ESSENTIAL SAFETY SET

Бренд: Safety 1st Страницы: 2

Бренд: Gaspo Страницы: 20

Бренд: Luxibel Страницы: 14

Бренд: Petzl Страницы: 2

Бренд: Spectra Страницы: 2

Бренд: wendi toys Страницы: 12

Бренд: Guardian Fall Protection Страницы: 15

Бренд: Major tech Страницы: 4

MULTI TESTER PRO

Бренд: Autodiagnos Страницы: 39

Бренд: OPW Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды