SportsPlay Quick Ship 3 Modified Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 140

background image

March 10, 2014

5

922-121-W GUARD WALL WITH WHEEL

INSTALLATION INSTRUCTION

INSTALLATION STEPS CONTINUED

5)

Connect Four-Hole brackets to posts:

Now you need to install

the Four-Hole Brackets to the posts. The top of the, Guard Wall
with Wheel should be 38” from the surface of the deck to the top of
the panel. Once you have the top of the panel at the correct height
tighten the two 3/8”x1” Button Head bolts (6). The Four-Hole
Brackets get installed with the Self-Tapping Screws (4) and
Attachment Bracket Gaskets (5) make sure that the hole for the
3/8x 3/8” set screw is pointing down.

TIP: It’s easier to install

the self-tapping screws if you pre drill the holes in the post with
a #7 drill bit.

Install the Self-Tapping Screws into the holes you

have drilled in the posts with the Attachment Bracket Gasket
between the post and Four- Hole Attachment Bracket. (See detail
B)

__6)

Secure the Guard Wall with Wheel

to the Attachment

Bracket:

Install and tighten the

3/8x3/8” Set Screw (5) in the Four-

Hole Bracket. (See detail B)

__7

Install the Steering Wheel:

You will Need the ½” x 5” Hex

Bolt (10), eight ½” Flat Washers and one ½” Lock Nut. Place one
½” Flat Washer on the ½” x 5” Hex Bolt, insert this into the
Steering Wheel and place six more ½” Flat Washers on the ½”x 5”
Hex Bolt behind the Steering Wheel. Place this sub assembly into
the factory punched hole in the Guard Wall with wheel Bracket.
Place the remaining ½” Flat washer on the ½” Hex Bolt and secure
it with the ½” Lock Nut. DO NOT OVER TIGHTEN THE NUT.
THE STEERING WHEEL MUST SPIN FREELEY. (See Detail C)

«
...
88
89
90
91
92
...
»

Содержание Quick Ship 3 Modified













































































































































Отзывы:

Нет отзывов

Похожие инструкции для Quick Ship 3 Modified

Бренд: Jacobsen Страницы: 20

Бренд: LaserLiner Страницы: 56

Бренд: LaserLiner Страницы: 54

Бренд: MacDon Страницы: 46

Бренд: MacDon Страницы: 82

Бренд: MACDEV Страницы: 8

Бренд: MA lighting Страницы: 10

Бренд: Transpak Страницы: 9

Бренд: ABS Страницы: 12

Бренд: Matco Tools Страницы: 14

LED CYC LIGHT 48x3W RGBA

Бренд: Squareled Страницы: 19

Hart Scientific 9101

Бренд: Fluke Страницы: 17

DS-CDJ-250 MKII

Бренд: DAPAudio Страницы: 19

Бренд: Oakton Страницы: 2

Бренд: TCM Страницы: 8

Бренд: Swing-N-Slide Страницы: 40

Бренд: Hioki Страницы: 130

Бренд: InstruStar Electronic Technology Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды