SPM Machine Guard MG4-REF11A Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 32

background image

6

Machine Guard MG4-REF11 A

SPM Instrument AB

• Box 504 • SE-645 25 Strängnäs • Sweden

Technical data are subject to change without notice.

Tel +46 152 225 00 • Fax +46 152 15075 • [email protected] • www.spminstrument.com

ISO 9001:2000 certified © SPM 2017-09. 71947 B

↑

↑

Power

Relays

Analog current

SPM transducer

VIB transducer

Front panel

Fuse (F):
230 VAC = T32 mA
115 VAC = T32 mA

Protective

earth

Main power switch

or circuit-breaker

F

230 VAC (115 VAC)

Make sure that the main power switch is

in off position and will stay off until the

work is done. Lock the switch if possible.

Cable inlets Pg11

Electrical installation of MG4

To connect an MG4-REF11A, remove the lower part of the front panel. The terminals of type push-
in for power supply and outgoing signals are situated beneath the lower part of the instrument
panel. Switch off the main power switch before removing the panel. A label on the rear side of the
cover shows the channel layout.

Power supply

The supply voltage can be 230 V AC or 115 V AC. Note that the power connection is labelled with
the factory set supply voltage for the unit. The fuse is a slow glass tube fuse rated T32mA. The
cable inlets (Pg11) are tight for cable diameters 5.5 to 10 mm. An adequately rated power cord
should be used.

The supply power should come via an external main power switch or a circuit-breaker, from a
power source with an even load (nominal voltage ± 10%, no excessive transients). The switch or
circuit-breaker must be suitably located and easily reached. It must be marked as the disconnecting
device for the equipment. See the figure above for connection to mains power terminals. Check
that the unit is connected to protective earth, marked with IEC symbol, and that protective earth
is properly connected to the protective earthing conductor of the building.

Read the Safety Precautions on page 2 before performing electrical installation. If you are in doubt,
please contact your local SPM representative before installing the equipment.

«
...
6
7
8
9
10
...
»

Содержание Machine Guard MG4-REF11A

































Отзывы:

Нет отзывов

Похожие инструкции для Machine Guard MG4-REF11A

LM-OG-P2 Advanced

Бренд: Badger Meter Страницы: 48

Бренд: Badger Meter Страницы: 24

Бренд: Bahco Страницы: 92

Бренд: Hama Страницы: 6

Бренд: M-system Страницы: 13

Бренд: WalkLAB Страницы: 16

Бренд: Sensia Страницы: 16

Бренд: Kawai Страницы: 8

Бренд: Dräger Страницы: 538

SF6 Portable Monitor

Бренд: Bacharach Страницы: 2

Arrow Mobile Android

Бренд: MADDALENA Страницы: 12

Бренд: Hanna Instruments Страницы: 15

Бренд: horiba Страницы: 10

Бренд: Hanna Instruments Страницы: 32

Бренд: Hanna Instruments Страницы: 2

Бренд: Cewe Страницы: 8

Celviano AP-650M

Бренд: Casio Страницы: 84

Бренд: KRAL Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды