SPM Machine Guard MG4-REF11A Скачать руководство пользователя | Manualshive

Страница: 21 / 32

background image

Machine Guard MG4-REF11 A

19

SPM Instrument AB

• Box 504 • SE-645 25 Strängnäs • Sweden

Technical data are subject to change without notice.

Tel +46 152 225 00 • Fax +46 152 15075 • [email protected] • www.spminstrument.com

ISO 9001:2000 certified © SPM 2017-09. 71947 B

Measuring direction

t

17

ø 27.5

54

9

Cable
clamp

ø 15

min. 12

max. 0.7

ø 6.9

(ø 5.5)

min. 16

min. 10

M8

(UNF
1/4”-28)

Vibration transducer installation

The transducer is mounted on the machine against a smooth, flat surface. M8 and UNF 1/4”-28
are the threads on the transducers. The transducer type TRV is supplied with three washers, each
of which changes the output direction 90°. The coaxial cable must be clamped close to the trans-
ducer. A sealed cable plug should be used for installations in moist environments.

As a rule, an insulation foot, either TRX-18 for M8 or TRX-19 for UNF 1/4”-28, should be used to
provide electric insulation when using transducers of type TRV. The reason is that differences in
earth potential between transducer and MG4-REF11A can cause measuring faults. Note, however,
that the installation foot limits the linear range of the transducer to ≈ 2000 Hz.

Flat-face mill the surface to a depth of max. 0.7 mm. To drill the mounting hole, use drill bit 6.9
mm for M8 and 5.5 mm for UNF 1/4”. Torque and unscrew the transducer with a 17 mm torque
wrench. The torque is 10 Nm.

TRV-18/19
TRV-20/21

SLD121
SLD122
SLD144

«
...
19
20
21
22
23
...
»

Содержание Machine Guard MG4-REF11A

































Отзывы:

Нет отзывов

Похожие инструкции для Machine Guard MG4-REF11A

Бренд: Xsens Страницы: 4

Бренд: Eastron Страницы: 2

Бренд: EASTERN INSTRUMENTS Страницы: 3

Бренд: ECO Sensors Страницы: 22

Бренд: ECO Sensors Страницы: 7

Бренд: F&F Страницы: 24

Бренд: Keithley Страницы: 32

Бренд: LATNEX Страницы: 55

Бренд: Laser Technology Страницы: 11

Бренд: Laser Technology Страницы: 62

LaserRange-Master T4 Pro

Бренд: LaserLiner Страницы: 68

DC1500 CHLORINE

Бренд: LaMotte Страницы: 60

Бренд: WalkLAB Страницы: 16

Бренд: YOSensi Страницы: 3

Бренд: Nidec-Shimpo Страницы: 6

SF6 Portable Monitor

Бренд: Bacharach Страницы: 2

Бренд: ACE INSTRUMENTS Страницы: 6

Бренд: C.R. Laurence Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды