Spedo 2600 страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 51

background image

23 |

S p e d o 2 6 0 0 O p e r a t o r M a n u a l

S p e d o U K L t d

23

Spedo 2600 Pinless Cutter Operator Manual

Check that this cycle is repeated until either the STOP is pressed or the
Continuous pushbutton is pressed once and released.

As a safety check, open the protective cover and check that none of the
above steps can be activated. Check also that the side trimmer shafts are
not rotating.

Repeat the safety check above with the main door removed.

Once  satisfied  that  the  forms  cutter  is  operating  satisfactorily,  install  any
other ancillary equipment that is to form the system (all instruction manuals
provided  with  Spedo  equipment  contain  installation  and  operating
instructions).  Connect  any system  leads  between the  forms  cutter  and  any
ancillary units as necessary.

Load the forms cutter with a paper web as shown in Fig 2.1 and align it as
shown in Fig 2.2.

Operate the combined system and check that it functions satisfactorily.
Before handing over, ensure that the operating personnel are familiar with
all operating procedures (as given in Section 3) and are aware of any safety
hazards involved

«
...
21
22
23
24
25
...
»

Содержание 2600




















































Отзывы:

Нет отзывов

Похожие инструкции для 2600

Бренд: Han-Bond Страницы: 58

Бренд: CAB Страницы: 16

Бренд: Westfalia Страницы: 90

Бренд: Profitech Diamant Страницы: 204

Бренд: Ellison Страницы: 18

Бренд: Bosch Thermotechnology Страницы: 267

Бренд: Shoprider Страницы: 20

Бренд: ES Equipment Страницы: 4

Бренд: Partner Страницы: 16

Бренд: Partner Страницы: 24

Бренд: Kronen Страницы: 30

Бренд: SU LEE MACHINE Страницы: 12

Бренд: KRAFTOOL Страницы: 6

Бренд: CAB Страницы: 22

Бренд: HSGM Страницы: 6

Бренд: Zenoah Страницы: 32

Бренд: Zenoah Страницы: 40

Бренд: IDEAL Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды