SpectraPure MaxCap MC-RODI-180-AF Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 32

background image

SpectraPure

®

SpectraPure

®

Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

4

SYSTEM SPECIFICATIONS:

Sediment Prefilter

0.5 micron MicroTec™ sediment prefilter (SF-MT-0.5-10)

Carbon Filter

0.5 micron carbon block prefilter (CF- 0.5-10)

RO Membrane Type

90 GPD SpectraSelect Plus TFC Membrane

(Use 2 for 180 GPD Systems)

DI Cartridges

MaxCap

®

Extended Life Super DI Cartridge (DI-MC-10HC)

SilicaBuster™ Extended Life Super DI Cartridge (DI-SB-10HC

)

Rejection Rate

Typical stabilized conductivity rejection 99%
Minimum conductivity rejection 98%

Input Water Pressure

60 psi (4.15 bar) line pressure*

Input Water Temp

77°F (25°C)

Recovery Rate

33% (i.e. 33% of the water will be collected as pure water)

Dimensions:

MaxCap MC-RODI-180-MF (-AF)

20" W x 16" H x 7" D (Two Membranes)

MaxCap MC-RODI-90-MF (-AF)

20" W x 16" H x 7" D (One Membrane)

Nominal Membrane Flow Rates @ 60 psi, 77° F, & 250 ppm TDS :

GPD Product Water Flow Rate

Concentrate Flow Rate (2:1)

90

234 ml/min

468 ml/min

180

468 ml/min

936 ml/min

Permeate flow and TDS rejection is based on the following test conditions:
250 ppm softened tap water, 77° F (25° C), 33% recovery and 60 psi.
Higher TDS, harder tap water, higher temperature, greater recovery rate, or
lower operating pressure may contribute to reduced permeate flow and/or
lower TDS rejection.

Reverse Osmosis Operating Limits:

Operating Pressure*

40 – 80 psi (2.75 – 5.5 bar)

pH Range

2 – 11

Maximum Temperature

113° F (45° C)

Maximum Turbidity

1.0 NTU

Maximum Silt Density Index

5.0 (based on 15 min. test time)

Free Chlorine Tolerance

less than 0.1 ppm

Maximum Iron

less than 0.1 ppm

Maximum Manganese

less than 0.1 ppm

Maximum Hydrogen Sulfide

0 ppm

*Operating pressure less than 40 psi may require a booster pump:
Operating pressure greater than 80 psi may require a pressure regulator.

«
...
2
3
4
5
6
...
»

Содержание MaxCap MC-RODI-180-AF

































Отзывы:

Нет отзывов

Похожие инструкции для MaxCap MC-RODI-180-AF

Бренд: ORMA Страницы: 5

Бренд: Brita Страницы: 5

Бренд: HOMBLI Страницы: 8

Бренд: A.O. Smith Страницы: 20

Бренд: Bluewater Страницы: 9

Бренд: Morphy Richards Страницы: 6

Бренд: Viking Страницы: 4

Бренд: Viking Страницы: 6

Envireau GL0052K

Бренд: Klargester Страницы: 30

Бренд: Parker Страницы: 2

Бренд: Laica Страницы: 8

Бренд: Laica Страницы: 17

Shadow RODI-40 Manual

Бренд: Phantom Страницы: 28

Бренд: Fahl Страницы: 88

Бренд: Graf Страницы: 22

Бренд: Kraftmann Страницы: 36

Бренд: Reverse Osmosis Страницы: 22

Бренд: Reverse Osmosis Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды