Spectra Watermakers VENTURA 150 Скачать руководство пользователя страница 10

Страница: 10 / 74

Components

Sea Strainer

Mount close to the intake through

hull, in a

location that can handle water spillage during service.

5 Micron Prefilter Bowl

Locate in an area that allows easy

access as this will be the most frequently serviced module while
cruising. Mount vertically and leave room below bowl for filter
changes.

Do not mount above water

sensitive equipment.

CAUTION

Feed Pump Module

Mount the feed pump module on a vertical surface, no more
than 3

feet (1.0M) above the waterline. It is preferable to

mount as low as possible. Locate in an area that allows easy
access to the charcoal filter, and the service valve. Keep
future maintenance in mind when choosing a location, and do
not mount above water

sensitive equipment.

NOTE:

IF INSTALLING THE Z±ION, SEE Z±ION

INSTALLATION INSTRUCTIONS FOR MORE DETAILS.

Содержание VENTURA 150











































































Результаты поиска

Содержание VENTURA 150

Отзывы:

Похожие инструкции для VENTURA 150

Бренды по названию

Популярные бренды

Spectra Watermakers VENTURA 150, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VENTURA 150

Отзывы:

Похожие инструкции для VENTURA 150

Бренды по названию

Популярные бренды