background image

72 

 

 

 

Spectra Watermakers Commissioning Report –

 

Page 1

 

(To be completed by authorized installer)

 

 

Fill out the below checks as completely as possible. Check any boxes that apply and note any concerns.

 

PURGE

 

□ 

Storage Chemicals have been purged with PRV open

 

Length of purge: _______Minutes

 

□ 

Diversion Valve is up, in reject position 

 

RUN HIGH MODE CHECKS

 

Product Flow: _____________ GPH/LPH 

 

Confirmed Product Flow Rate ___________GPH/LPH

 

□ 

Technician Flow meter. Brand________________

 

□ 

Hand Measurement _______Gal/Liters in _____SEC/MIN

 

Product Quality: __________ PPM 

 

□ 

Confirmed product quality with handheld TDS meter 

 

Feed Pressure: __________ PSI/BAR 

 

Brine Flow Rate: _______________ GPM/LPM

 

Measurement taken with:

 

□ 

Technician Flow meter. Brand_________________

 

□ 

Hand Measurement: _______Gal/Liters in _____SEC/MIN

 

Notes:_________________________________________________________________ 

______________________________________________________________________ 

 

FRESHWATER FLUSH 

 

□ 

Freshwater Flush solenoid valve opens

 

When seacock is open, what is the ppm of brine discharge at the end of the flush_______

 

Flush duration is ________Minutes

 

□ 

Needed to change flush time 

 

Notes:________________________________________________________________ 

______________________________________________________________________ 

 

*If the system does not have a dedicated forward

-

facing scoop type thru

-

hull or will be on a vessel that moves 

faster than 15 knots the system needs to complete the following sea trial checks. Spectra Watermakers 
reserves the right to require a sea trial from any customer before approving a commissioning report. 

 

SEA TRIAL

 

□ 

Watermaker will flush while underway

 

□ 

Watermaker will start while underway

 

While the vessel is underway moving _______KNOTS/MPH/KPH the watermaker is producing _______ GPH/

LPH at ______PPM

 

The following checklist is designed to confirm that the watermaker installation meets Spectra 

 

standards and that the system is performing at specification.

 

C

U

 H

ER

E

 

Содержание VENTURA 150











































































Отзывы: