Spearhead 8999082 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 21

Spearhead 8999082 Скачать руководство пользователя страница 18

18

18

18

18

Trident 7600HD

Storage

Storage

Storage

Storage

Before storing the unit, it must be thoroughly washed and grass and dirt must be removed.
When using a high pressure or steam cleaner you should exercise caution because of the
paint job. The grease gun should be used until fresh grease comes out of the grease
nipples. Power transmission shaft and drive belts should be stored in a dry place. Grass
juice leads to increased formation of rust! If the device is equipped with a hydraulic side shift,
the rod of the ram should be retracted to protect against rust. The unit should be kept as dry
as possible.

NOTE

NOTE

NOTE

NOTE

Couplings and transmission remain very hot. Do not touch directly after use!

Checklist for maintenance (Further details are listed in the respective sections.)

Ongoing inspection Transmission: Flanges and bolts (seated/tight?) Check.

Flail shaft: tightness of bolts, Check (especially on stock) and condition of

the hammer knives.

Daily inspection

Check V-belt tension.

Check the gearbox oil level.

Lubricate all parts of the drive shaft.

All locations. See Lubrication Drawing.

Annual inspection Oil levels in gearboxes ( EP-90).

«
...
16
17
18
19
20
...
»

Содержание 8999082






















Отзывы:

Нет отзывов