Spearhead 8999082 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 21

Spearhead 8999082 Скачать руководство пользователя страница 15

Trident 7600HD

Lubrication

Lubrication

Lubrication

Lubrication

The lubrication points for the daily greasing

Figure 6
Lubrication points for the cross
cross-shaft bearings, rotor and rear
roller bearings.

Warning

Warning

Warning

Warning

for

Bearing for the roto
least once every 8 hours of operation and a
machine. In case of heavy load, the machine should be lubricated more
often.

Fig 7

Figure 7
Profile tubes for power transmission must be removed, cleaned and lubricated. The crosses are to
be lubricated, also.

15

15

15

15

Trident 7600HD

the daily greasing can be seen below.

for the cross-shaft,

and rear

for the rotor shaft and the rear roller should be lubricated at

least once every 8 hours of operation and after each cleaning of the

In case of heavy load, the machine should be lubricated more

Fig 7

for power transmission must be removed, cleaned and lubricated. The crosses are to

r shaft and the rear roller should be lubricated at

fter each cleaning of the

In case of heavy load, the machine should be lubricated more

Fig 6

for power transmission must be removed, cleaned and lubricated. The crosses are to

«
...
13
14
15
16
17
...
»

Содержание 8999082






















Отзывы:

Нет отзывов