Spearhead 8999082 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 21

Spearhead 8999082 Скачать руководство пользователя страница 17

17

17

17

17

Trident 7600HD

Maintenance and adjustment of the slip clutch

Maintenance and adjustment of the slip clutch

Maintenance and adjustment of the slip clutch

Maintenance and adjustment of the slip clutch

Prior to commissioning and after long downtimes check the condition of the friction clutches.
Release the spring tension and rotate the clutch while the PTO drive is being held. Once
freed off, re- adjust the spring tension to the original setting.
After the work season release the spring tension and keep the clutches covered in a dry
place. Check the condition of the friction plates and adjust the spring tension to the original
height before use.
If the clutch has been overheated due to frequent and sudden slipages, disassemble the
clutch and check. The original thickness of the clutch lining is 3.2 mm and the coating has to
be replaced when it has reached a thickness of 2.5 mm. Clean all contact surfaces and
replace any defective components before the clutch is re-assembled and used.

A

A

A

AT

T

T

TT

T

T

TE

E

E

EN

N

N

NT

T

T

TIIIIO

O

O

ON

N

N

N!!!!

The dimension setting 'h' relates to newer types of coupling, in which the two plates, which
are measured, have the same diameter.

Type

Position

Part No.

Setting

Nm

FV34R

Center

5770206

17,6 mm

1500

FV42

Wing

5770039A

19,7 mm

1200

Warning

Warning

Warning

Warning

The slip clutch is used to protect the transmission. If the blades hit a
large object, they can be damaged or broken. This is to be avoided.

«
...
15
16
17
18
19
...
»

Содержание 8999082






















Отзывы:

Нет отзывов