manualshive.com logo in svg

Space-Ray PCA-SS 100, Инструкции по сборке, установке и эксплуатации, Страница: 1 / 62

Поделиться
Скачать
Space-Ray PCA-SS 100 Скачать руководство пользователя страница 1

Form 43343110 

May 2021 

 

 

 

INSTALLATION AND OPERATION INSTRUCTIONS 

INFRARED RADIANT POULTRY/SWINE TUBE HEATER 

Single and Two Stage Push Through System (Positive Pressure) 

 

THE DEFENDER

 

Models:

 

 

PCA-SS 75 (N5,L5,N7,L7 
PCA-SS 100 (N5,L5,N7,L7 
PCA-SS 125 (N5,L5,N7,L7 
PCA-SS 150 (N5,L5,N7,L7 

 

FOR  YOUR  SAFETY:  Exhaust  fans  MUST  be  operating  on  an  appropriate  cycle  when  heaters  are  operating  to 
avoid a  high  concentration  of carbon  monoxide. When  used without fresh  air,  this heater may  give off carbon 
monoxide, an odorless and poisonous gas. CARBON MONOXIDE POISONING MAY LEAD TO DEATH. Early signs of 
carbon  monoxide  poisoning  resemble  the  flue  with  headaches,  dizziness  and  nausea.  If  you  experience  these 
signs, GET FRESH AIR IMMEDIATELY! Have the heaters serviced as soon as possible and check the ventilation in 
the house. 

 

These heaters are designed for agricultural applications and may operate with the use of either Natural Gas or 

Liquid  Propane  (LP)  Gas.  Check  the  heater’s  nameplate  to  determine  the  correct  gas  type  before  proceeding 

with installation. 
 

!INSTALLER:

 This manual is the property of the owner. Please present this manual to the owner when you leave 

the job site. 

 

 

   

IF YOU SMELL GAS: 

FOR YOUR SAFETY 

 

!

 

DO NOT try to light any appliance. 

!

 

DO  NOT  touch  any  electrical  switch;  DO  NOT  use  any 
telephone in your building. 

!

 

IMMEDIATELY  call  your  gas  supplier  from  a  neighbor's 
telephone.  Follow  the  gas  supplier's  instructions.  If  you 
cannot reach your gas supplier, call the fire department. 

 

 
 
DO NOT store or use gasoline or other 
flammable vapors and liquids in the vicinity of 
this or any other appliance.

 

 

 

 
 
 

 

!IMPORTANT: SAVE THIS MANUAL FOR FUTURE REFERENCE. 

SPACE-RAY 

Post Office Box 36485 (28236)  

•  

1700 Parker Drive (28208)  

•  Charlotte, North Carolin

a 

Phone  (704) 372-3488  

•  Fax  (704)

 332-5

843  •  www.spaceray.com  •  email:  [email protected]

 

OWNER 

/

 INSTALLER: 

For your safety this manual must be carefully and thoroughly read and understood before 

installing, operating or servicing this heater. This heater is intended for use with either  Natural Gas or Propane 
Gas. It must be installed by a qualified service person or a licensed contractor in accordance with state and local 
codes. In the absence of these codes, the installation must conform to the National Fuel Gas Code ANSI Z223.1 
(latest edition), also known as NFPA54 or the Natural Gas and Propane Installation Code CSA B149.1 in Canada. 

 

▲WARNING:

 Improper installation, adjustment, alteration, service, or maintenance can cause property damage, 

injury  or  death.  Read  the  installation,  operation  and  maintenance  instructions  thoroughly  before  installing  or 
servicing this equipment. For assistance or additional information, consult a qualified installer, service agency or 
the gas supplier. 

 

INSPECT all combustion air openings into the building and, if necessary, clear as they become blocked by litter, 
dust, feathers or other matter.

 

Scan warranty QR code on the right to 
register your product. 

 

Содержание PCA-SS 100































































Отзывы:

Нет отзывов