Spa Builders MC-MP-SBD Скачать руководство пользователя | Manualshive

Страница: 9 / 47

background image

MC-MP-SBD Owner’s Manual

8

Important Safety Instructions

Important Notice

Warning

All electrical connections must be carried out by a qualified
electrician in accordance with national and/or local electrical
codes in force in the state or province at the time of installa-
tion. When connecting equipment, always refer to the wiring
diagram included on the inside plastic cover of your spa pack
power box. It will always take precedence over the wiring
diagram provided at the end of the present manual.

Total current ouput cannot exceed total input rating!

RISK OF ELECTRICAL SHOCK!

Install at least 5 feet (1.5 m)

from any metal surface. Do not allow any electrical appliance
within 5 feet (1.5 m) of the spa. Strictly conform to all safety
instructions provided by your spa manufacturer.

Low voltage or improper wiring may cause damage to the
MC-MP-SBD control system. Carefully read and follow all
wiring instructions when connecting to power supply. Dam-
age caused by improper wiring or installation is not covered
under the MC-MP-SBD warranty.

This pack contains no user-serviceable parts. Please contact
an authorized service center for service.

Electrical Hazard

Caution

Repairs

General Information

«
...
7
8
9
10
11
...
»

Содержание MC-MP-SBD
















































Отзывы:

Нет отзывов

Похожие инструкции для MC-MP-SBD

SOAKER BATH SERIES

Бренд: Jacuzzi Страницы: 48

OPTICA HANDLE KIT

Бренд: Jacuzzi Страницы: 2

Бренд: Aquatic Страницы: 1

Бренд: Aquatic Страницы: 1

Бренд: QCA Spa Страницы: 10

Byron Luxury Spa

Бренд: Aqua Pulse Spas Страницы: 5

Бренд: Jacuzzi Страницы: 46

Бренд: LAZBOY Страницы: 48

Бренд: SpaDealers Страницы: 8

Бренд: J&J Sanitary Ware Страницы: 15

Бренд: Kohler Страницы: 4

ZENKURU PH050017

Бренд: COOLSTUFF Страницы: 26

Бренд: HoMedics Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды