Spa Builders MC-MP-SBD Скачать руководство пользователя

Страница: 43 / 47

MC-MP-SBD Owner’s Manual

Error Displays

Alarm & Error Displays

Flashing dots means the system has detected a problem with the pressure switch
(water flow related error message) or the Hi-limit probe protection.

3 flashing dots are displayed:

A problem has been detected.

Do not enter the water! Check and open water valves. Clean filter if
necessary. Check water level. Add water if necessary.

Shut power off and power your spa up again to reset the system.

Call your dealer or service supplier if problem persists.

Water temperature is flashing:

Water temperature in the spa has reached 112˚F (44˚C).

Do not enter the water! Allow water to cool down. The system will
reset itself when water tem-perature reaches 109˚F (43˚C).

Call your dealer or service supplier if problem persists.

Содержание MC-MP-SBD
















































Результаты поиска

Содержание MC-MP-SBD

Отзывы:

Похожие инструкции для MC-MP-SBD

Бренды по названию

Популярные бренды

Spa Builders MC-MP-SBD, Руководство пользователя

Результаты поиска

Содержание MC-MP-SBD

Отзывы:

Похожие инструкции для MC-MP-SBD

Бренды по названию

Популярные бренды