manualshive.com logo in svg

Spa Builders MC-MP-SBD, Руководство пользователя

Поделиться
Скачать
Spa Builders MC-MP-SBD Скачать руководство пользователя страница 32

MC-MP-SBD Owner’s Manual

31

MC-MP-SBD Operation and Functions

On/Off Key

Jet Keys

By default, the system is 
always on as soon as it is 
under power. The unit will 
regulate the spa tempera-
ture to the desired Set 
Point and the display will 
show the current water 
temperature.

Press 

On/Off

 key to shut 

the system down (i.e., to program Stand-By mode) for 
30 minutes. The "OFF" message will be displayed. All keys will be 
disabled until you press 

On/Off

 again to reactivate the system 

before the expiration of the 30-minute delay.

Pump keys are used to 
turn Pump 1, Pump 2 on 
or off, and to select be-
tween low and high 
speeds.

Press 

Pump 1 

or 

Pump 2

to turn Pump 1or 2 on at 
low speed. Press a second 
time to change to high 
speed for dual-speed 
pump configuration. 
Press a third time to turn 
the pump off.

The "Pump 1" or "Pump 2" indicator lights up on the display 
when either pump is on at high speed. It flashes when either 
pump is on at low speed.

A built-in timer will turn either pump off after a predetermined 
period of time (see low level programming page 25), unless they 
have been manually turned off first.

1st press  =  low speed
2nd press  =  high speed 

(for dual-speed pump)

3rd press  =  off

"Pump 1" light indicator

Operating Instructions

Содержание MC-MP-SBD
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды