manualshive.com logo in svg

Spa Builders MC-MP-SBD, Руководство пользователя

Поделиться
Скачать
Spa Builders MC-MP-SBD Скачать руководство пользователя страница 24

MC-MP-SBD Owner’s Manual

23

Loosen the four screws that secure the plastic cover of your 
spa pack’s power box and remove the cover.

The main spa side keypad must be connected to the standard 
side panel port of the power box.  A cable is provided to 
connect the control keypad to the board inside the power 
box.  Attach the connector to the board as shown below.

Connecting to the 
Power Box

Warning

Keypad 
cable

Keypad

Power box

Clearance between low and high voltage conductors must be at 
least 1/4" (6 mm).

Connecting the
Temperature
Probe

The water temperature 
probe must be similarly 
connected to the port 
labelled "TEMP" on the 
board, with the cable 
following the same route as 
the main control keypad.

Proper way to connect keypad to

standard "Side panel" port:

Cable facing the left

side of the box

Header

Pins slide

into the cable head

Horizontal-heater model

Main Keypad & Temperature Probe

Installation

Содержание MC-MP-SBD
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды