Spa Builders MC-MP-SBD страница 38 Скачать руководство пользователя | Manualshive

Страница: 38 / 47

background image

MC-MP-SBD Owner’s Manual

37

Keypad Lockout

Your spa keypad can be locked. This feature is especially useful if
young children have access to the keypad.

To Partially lock the keypad:

Press and hold

Pump 1

key

for 5 seconds.

If properly programmed, the
"LOCP" message will appear
briefly on the display. In this
mode, only the pumps,
blower and light keys are accessible.
If any other key is pressed, the attempted function is rejected
and the "LOCP" message is displayed for 1 second.

To Fully lock the keypad:

Press and hold

Pump 1

key

for 10 seconds.

If properly programmed, the
"LOCF" message will appear
briefly on the display. In this
mode, only automatic func-
tions are allowed. If any key is pressed, the attempted func-
tion is rejected and the "LOCF" message is displayed for 1 second.

To unlock the keypad:

Press and hold

Pump 1

key again for 5 seconds. If properly

programmed, the system will return to Normal mode, and all
functions will be accessible.

N.B.: A power failure will unlock the keypad causing it to return to
Normal mode

MC-MP-SBD Operation and Functions

Operating Instructions

«
...
36
37
38
39
40
...
»

Содержание MC-MP-SBD
















































Отзывы:

Нет отзывов

Похожие инструкции для MC-MP-SBD

Бренд: Jacuzzi Страницы: 28

Бренд: Grohe Страницы: 52

Бренд: Detox Страницы: 6

Бренд: Canadian Spa Страницы: 4

Бренд: Canadian Spa Страницы: 14

Бренд: MAAX Страницы: 71

Бренд: Jacuzzi Страницы: 64

Бренд: Balboa Water Group Страницы: 2

Бренд: Jacuzzi Страницы: 52

Бренд: Jacuzzi Страницы: 104

Бренд: albatros Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды