Visit: www.aquapulsespas.com.au
BYRON LUXURY SPA START UP INSTRUCTIONS
Remove the filter from the spa, see page 8 in your user manual.
Place a hose in the filter box to fill the spa with water, see page 7 in your user manual.
Remove the fittings from your hose to prevent them falling into the spas plumbing.
Set your main diverters on the spa to the centre so that both sides of the spas plumbing will fill up with water.
Refer to page
9
your user manual to locate the main diverters.
Fill the spa until the water level covers the top of the highest jet, then place your filters back in the spa.
Note
: It is extremely important that you fill your spa with water and fit the hardcover as soon as the spa is put
outside even if your electrician is not coming straight away.
Your hardcover must always be on the spa when not in use, and the spa must always be filled with water. An
empty spa on a hot day will cause melting, crazing, discolouration and blistering in the spas acrylic and fittings.
This can happen within 10 minutes of the spa being emptied. Your warranty will be made void if you leave the spa
empty for any length of time.
The screws to fit your hardcover clips onto the spas cabinet are taped to the packaging on the spa, make sure you
locate them before you dispose of the packaging. In the same pack there will be a drain fitting which you will need
when it comes time to drain the spa. On the hardcover itself you will find the clips which you need to screw onto
the spas cabinet to lock the hardcover down. On one of these clips there will be a small plastic bag attached which
will have the keys you will need to lock the cover.
Your spa has an inbuilt aroma therapy stick, you can locate it on page 1 in your user manual. With the power
turned off unscrew the fitting by turning it anticlockwise from the spa, this will remove the fixing lid and you will
now see a D shaped handle which you need to lift upwards to remove it. You should now have the aroma therapy
canister in your hand, the canister has a plastic transport cover which needs to be removed. You can remove it
by unscrewing the blue cap and sliding the opaque cover off which will expose the scented stick inside, screw the
blue cap back onto the aroma stick leaving the opaque cover off. Reinstall the stick back into the spa, do not
overtighten the fitting it only needs to be lightly tightened. From here turning the D handle clockwise runs the
aroma therapy scent when you have the air blower turned on and turning the D handle anticlockwise will turn the
aroma therapy scent off.
NEVER CONNECT POWER USING AN EXTENSION LEAD.
Have a qualified electrician connect the spa to power. The power supply your electrician needs to connect is
32Amp Dedicated Single Phase connection with the appropriate sized Residual Current Device in your
houses metre box. Please refer to page 5 through to page
6
of your user manual. The panels to remove from
the spa to find the electrical connection point will be the panels directly underneath the digital touch pad on the
spa.
Your electrician can drill a hole anywhere through the fibreglass base to pull the electrical cable through.
Just make sure that the area behind where they drill is clear of any spa parts inside the cabinet.
Once the spa has power connected to it and it is filled with water turn the power on. Never turn the spa on if
you do not have it filled with water.
While your electrician is still on site, put the spa into Active mode, see page 11 in your user manual.
Once you are in active mode press Jets 1, see page 12 in your user manual.
You should now have water movement within the spa, let the spa run for 5 minutes then press Jets 1 to turn
the pump off.
If you have no water movement at this stage have your electrician contact the store while they are still onsite.
Now go to page 13 in your user manual and follow the instructions to set the time of day.
Now go to page 13 in your user manual and follow the instructions to set the cycle cleaning.
Now go to page 14 in your user manual and follow the instructions to set the cycle heating.
Now go to your weekly chemical instructions and balance the spas water.