Sortimo ProCargo CT1 Скачать руководство пользователя страница 24

46

47

To unlock the frame lock:

•  Insert the key and turn in a clockwise direction. The half-ring snaps back 

automatically.

•  Release the key and remove.

4.6.  Pannier holders

The Wingee mudguards feature integrated side struts for the mounting of panniers. 

Each side can carry a maximum load of 8 kg.

5. 

Ergonomic setting

5.1.  Horizontal saddle position and tilt

The optimum horizontal saddle position can be 

determined using the „knee plumb line“.  

The knee plumb line can be determined using a 

weight suspended on a piece of string.  

The knee plumb line should pass through the 

pedal axle or just in front of it.

Sit on the pedelec in the position shown above with horizontal crank arms and have 

a second person determine the knee plumb line.

Ideally, the saddle is horizontally aligned with the upper side or with the saddle tip 

tilted slightly forwards.  

To adjust the saddle position and tilt, loosen the 

two Allen screws of the saddle clamp situated 

behind the seatpost under the saddle. 

You can now shift the saddle in the guide of the 

clamp and adjust the tilt. 

Then tighten both screws with 9-10 Nm.

Ergonomic setting

5.2.  Adjusti ng grip distance of the brake lever 

The grip distance can be adjusted using an Allen 

key at the positi on marked in red. 

The grip distance of the brake lever should be   

adjusted so that it is possible to wrap the 

 foremost phalanges of 2-3 fingers behind the 

brake lever. 

6. 

Maintenance

Regular maintenance of the cargo bike will ensure that it remains safe and 

 functional. Please observe the following information before every maintenance 

measure.    

Sortimo offers a service concept. Get in touch with your direct Sortimo 

contact person or the Sortmio Service Team. 

Maintenance requires technical skills. You are responsible for the 

 maintenance work being carried out correctly. 

-> If you do not feel confident doing the work, have the bike serviced  

by a dealer or contact the Sortimo Service. 

Risk of clamping and crushing if the mainte-

nance work is carried out with the drive unit 

switched on! Your hands could get stuck in 

the moving drive between belt and socket. 

-> Always remove the battery before com-

mencing any maintenance work. 

Risk of clamping and crushing when carrying out maintenance work.  

Your fingers could get stuck between moving parts. 

-> Pay attention to your hands and work carefully. 

Maintenance   

Содержание ProCargo CT1


































Отзывы: