SORIN GROUP S5 System Скачать руководство пользователя страница 81

Страница: 81 / 191

S5 System • Fault messages and troubleshooting

SM-5811-0000.01 ENG

5.5

Battery fault

Display in system menu

Description

➜

possible cause/effect

◗

Steps to be taken (please proceed in the order listed)

Battery is a high-drain battery.

The battery charge time was exceeded (internal charge time

limit approx. 3 hours)

Deviation of current measured voltage value from specified

actual value detected internally during trickle charging.

(Internal) fault has occurred during storage of battery capacity.

Battery fault detected.

A software fault has occurred in the UPS.

The following applies to all these messages:

➜

One or both batteries is/are defective

➜

UPS module fault

◗

Replace battery (-ies)

◗

Replace UPS module

Charging time too long

The residual charging time was too long

Fault during trickle charging

No battery capacity stored

Stored battery capacity incorrect

Battery voltage = 0.5 V!
The battery is defective

UPS is defective

Содержание S5 System
































































































































































































Результаты поиска

Содержание S5 System

Отзывы:

Бренды по названию

Популярные бренды

SORIN GROUP S5 System, Инструкция по эксплуатации

Результаты поиска

Содержание S5 System

Отзывы:

Бренды по названию

Популярные бренды