Sony XCL5005 Скачать руководство пользователя страница 45

Страница: 45 / 56

Camer

Con

Command

Command Specification

[Process] Selects an input route of the external trigger

signal.

Flip-flop Output Setting (XCL-5005 only)

[Command] FLIP-FLOP
[Parameter 1] <Mode (0 - 1)>

0: OFF
1: ON

[Process] Sets the flip-flop of image output.

Grayscale Output Setting (XCL-5005 only)

[Command] GRAYSCALE
[Parameter 1] <Mode (0 - 1)>

0: OFF
1: ON

[Process] Sets the grayscale mode.

Color Bar Output Setting (XCL-5005CR only)

[Command] COLORBAR
[Parameter 1] <Mode (0 - 1)>

0: OFF
1: ON

[Process] Sets the color bar output mode.

DC IN Connector Signal Output Setting

[Command] WEN-STRB
[Parameter 1] <Specification for 10th pin output (0 - 2)>

0: GND output
1: DVAL output
2: EXPOSURE output

[Process] Sets the 10th pin of DC IN connector signal

output specification.

Image Output Data Width

[Command] IMG-WIZE
[Parameter 1] <Image output data width (0 - 3)>

0: 12 bit output
1: 10 bit output
2: 8 bit output
3: RGB 24 bit output (XCL-5005CR only)

[Process] Sets the image output data width.

Image Output Data Tap

[Command] IMG-TAP
[Parameter 1] <Image output data tap (0 - 1)>

0: 80 MHz 1TAP output
1: 40 MHz 2TAP output

[Process] Sets the image output data tap.

Serial Transmission Speed Setting

[Command] BRATE
[Parameter 1] <Baud rate (0 - 3)>

0: 9600 bps
1: 19200 bps
2: 38400 bps
3: 57600 bps

[Process] Sets the serial transmission speed.

Setting Value Control Command

The setting value control command controls camera
setting data saved in the Flash ROM inside the camera.
The following list shows the contents.

Setting Initialization Command

Note

Some data are not initialized by executing the following
commands. For details, refer to “Parameter List” on
page 51.

Initialization of Setting

[Command] INIT
[Process] Initializes the data corresponding to the

camera control command to the factory setting value.

Save Setting Command

Save Setting

[Command] SAVE
[Process] Writes the data corresponding to the camera

control command in the Flash ROM.
Another command is not accepted during execution
of the process. After completion of execution, the
following message is displayed.

“OK”: Normal completion

Note

If the completion is not normal, the saved data may be
damaged.

Read Setting Command

Read Setting

[Command] LOAD
[Process] Reads the data corresponding to the camera

control command in the Flash ROM.

Command

Explanation

Initialization
of setting
value

Initializes the data corresponding to the
camera control command to the factory
setting value.

Save setting

Writes the data corresponding to the camera
control command in the Flash ROM.

Read setting

Reads the data corresponding to the camera
control command in the Flash ROM.

Setting value
accession

Sends the necessary data to the camera
control application.

Содержание XCL5005

























































Результаты поиска

Содержание XCL5005

Отзывы:

Бренды по названию

Популярные бренды

Sony XCL5005, Техническое руководство

Результаты поиска

Содержание XCL5005

Отзывы:

Бренды по названию

Популярные бренды