manualshive.com logo in svg

Sony XCL5005, Техническое руководство

Поделиться
Скачать
Sony XCL5005 Скачать руководство пользователя страница 9

Ov
e

rvi

ew

Location and Function of Parts and Operation

9

In the case of non-PoCL support:

Both the 1st pin and 26th pin are 
INNER_SHIELD (Ground)

Note 

When you operate a camera module by inputting an 
external trigger signal via the 26-pin connector, make 
sure to input external trigger signals that meet the 
following specifications to both the two pins.

Specifications for the External Trigger Signal
Amplitude:

LVDS using a 3.3 volt IC

Connections: Input a TRIG (–) signal to the 9th 

pin.
Input a TRIG (+) signal to the 22nd 
pin.

Polarity:

Positive 

Connecting the cables

Connect the camera cable to the DC IN connector and 
the Camera Link cable to the digital interface cable 
respectively. If you use a camera module interface board 
with support for PoCL, you can operate the camera even 
if you do not connect the camera cable to the DC IN 
connector. When you connect the Camera Link cable, 
turn the two fastening screws on the connector to secure 
the cable tightly.
Connect the other end of the camera cable to the DC-
700/700CE and the other end of the Camera Link cable 
to the camera module interface board.

Note 

When using the camera with a PoCL connection, make 
sure you connect a PoCL compatible cable. Connecting 
a cable that is not compatible with PoCL (non-PoCL) 
may cause a malfunction of the camera or camera 
module interface board.

Controlling the camera from the host 
device

You can control the camera from host device such as a 
computer. The following table shows the control 
functions. 
You can send a command corresponding to the control 
items, with parameters for the desired settings, if 
necessary, from the host device to control the camera.

Refer to “Camera Control Commands” on page 39 for 
details on how to send a command, the commands, and 
their parameters.

Note 

Make sure to supply power to the camera module and 
confirm that the camera module is operating before 
inputting a trigger signal. If you input trigger signal to a 
camera module without the power supplied, this may 
cause a mulfunction of the camera module.

Trigger signal specifications

Input impedance: Stated in the voltage determined at 
more than 10 k ohms

b

a

c

d

e

Digital interface connector

Camera Link cable

Fastening screws

DC IN 
connector

Camera cable

Control functions

Description

Operating mode

Normal/Trigger

Shutter speed

Normal

2 to 1/10000 s

Trigger edge

2 to 1/10000 s

Trigger pulse 
width

Setting by 
trigger pulse 
width

Gain

0 to +18 dB

Partial Scan

OFF/ON

Gamma control

OFF/ON (Mode 1 to 7)

External trigger input

26 pin connector/12 pin connector

Video output switch

12 bits/10 bits/8 bits

Swtich output tap

1TAP/2TAP

White balance 
(XCL-5005CR only)

PRESET/MANUAL/ONE PUSH 

(AUTO)

Switch color output 
(XCL-5005CR only)

RAW data/RGB data

Binning (XCL-5005 only)

OFF/ON

Edge detection, Edge 
enhancement (XCL-5005 
only)

OFF/ON

Binarization (XCL-5005 
only)

OFF/ON

3×3 image filtering 
(XCL-5005 only)

OFF/ON

DC IN terminal

90%

10%

2 - 5 V

10.0 µs - 2 s

Width

0 - 0.6 V

Rising time

Less than 
2.0 µs

Amplitude

Содержание XCL5005

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды