manualshive.com logo in svg

Sony XCL5005, Техническое руководство

Поделиться
Скачать
Sony XCL5005 Скачать руководство пользователя страница 5

Ov
e

rvi

ew

System Components

5

System Components

Video Camera Module
XCL-5005CR/5005

Camera cable
CCXC-12P02N (2 m, 6.6 ft)
CCXC-12P05N (5 m, 16.4 ft)
CCXC-12P10N (10 m, 32.8 ft)
CCXC-12P25N (25 m, 82 ft)

C-mount lens
High-resolution lens

Camera adaptor
DC-700/700CE

Tripod adaptor
VCT-ST70I (Insulated type)

Camera Link cable
(Sony Camera-compatible)

Camera module interface 
board

Install the board in a PCI bus slot in devices such as a computer. Select a commercially available interface 
board compatible with the Camera Link feature. You can use either a board that supports PoCL, or one 
that does not.
In the board corresponding to PCI 32 bit, the frame rate may become low according to lack of processing 
capacity. When you want to make this product output 15 frames per second, use a board corresponding 
to more than PCI 64 bit (PCI-X).
When you use XCL-5005CR with RGB data output, the frame rate may become low because of insufficient 
processing capacity even if you use a PCI 64 bit compatible board. If you want to output 15 frames of 
images every second, use a PCI Express board. Performance may also be dependent on the host device 
(e.g., Computer), so consult the dealer if images are not displayed properly.

This cable connects to the digital interface connector on the rear panel of the camera module. Image/
control signals are transmitted via this cable.
If there is support for PoCL, power is also supplied at the same time. If you use a camera module interface 
board with support for PoCL, be sure to use a camera link cable with support for PoCL. You can use a 
single cable up to 7 meters long in the case of 1TAP output, and extend the cable length even further in 
the case of 2TAP output. Select a proper cable as the maximum usable length of a cable differs due to the 
attribute of each cable.
Spotted noise may appear in a specific brightness in the window according to the attribute of the cable. If 
this noise is an obstacle, shorten the cable.

Содержание XCL5005

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды