25
MEX-1HD
6. With the track number 1 selected, press the right jog button
(PUSH LIST). (A check mark will be displayed on the right
side of track number 1 only)
7. Press the
[ REC]
button to start the recording.
8. Check that the progress bar is processing and remaining amount
of time for recording indicated next to the bar is decreasing.
9. Press the function 1 (
s
) button to quit recording.
Ver 1.2
dial (PUSH LIST), and press the right jog button (PUSH LIST)
to enter the ID COPY mode.
9. Input the password for ID copy with the right jog dial and
button (PUSH LIST).
10. Rotate the right jog dial (PUSH LIST) to select the “(OK)”,
and press the right jog button (PUSH LIST) to execute ID copy
to the HDD of the system ID.
11. Upon successful completion of ID copy, if the “ID-COPY OK”
is displayed, release the test mode. (Power off)
• Data installing to the HDD (User Upgrade type only)
Note 1:
This operation is required for the User Upgrade type only. For
Initial Lot type, skip this operation and go to the next step “Op-
eration check”.
Note 2:
Data installing may fail, if there is less available space in the
hard disk.
If data installing failed, make a checking through the following
procedure. Less space remains if “FULL CAPACITY” is dis-
played.
Checking procedure:
(1) In the standby state with normal mode, press the
[M]
(MENU)
button to display the menu screen.
(2) Rotate the right jog dial (PUSH LIST) to select the “Library”,
and press the right jog button (PUSH LIST) to enter the Li-
brary mode.
(3) Rotate the right jog dial (PUSH LIST) to select the “CDDB
Install”, and press the right jog button (PUSH LIST) and
display confirmation screen of start the processing.
(4) Rotate the right jog dial (PUSH LIST) to select the “OK”,
and press the right jog button (PUSH LIST). Less space re-
mains if “FULL CAPACITY” is displayed.
1. When the power is turned on, the initial setting screen is dis-
played. Press the right jog button (PUSH LIST) button repeat-
edly until tentative setting completed.
Note:
Exact date and time need not be set.
2. Chech the version of CD-R for service and insert the disc to
the set.
3. Again in the test mode, select the “Test Mode” from the test
mode main menu by rotating the right jog dial (PUSH LIST)
and press the right jog button (PUSH LIST) to enter the Test
Mode.
4. Rotate the right jog dial (PUSH LIST) to select the “IN-
STALL”, and press the right jog button (PUSH LIST) to enter
the INSTALL mode.
5. Rotate the right jog dial (PUSH LIST) to select the “ALL(U)”,
and press the right jog button (PUSH LIST), and the “IN-
STALL-ALL(U) “ will be displayed and the installation will
start soon.
(process time: about 30 minutes)
6. Upon successful completion of installation, the “INSTALL-
ALL(U) OK” will be displayed, and then remove the CD-R
for service and release the test mode. (Power off)
• Operation check
1. Turn the power on again, and the initial setting screen will be
displayed. Then, press the right jog button (PUSH LIST) but-
ton repeatedly until tentative setting completed.
Note:
Exact date and time need not be set.
2. In the normal mode, press the
[SOURCE]
button to select the
HDD mode and play recorded contents. Check that the recorded
contents are played back normally.
3. Insert a music CD and press the
[SOURCE]
button to play.
4. Press the
[ REC]
button, rotate the right jog dial (PUSH
LIST) to select the third item (musical note mark), and press
the right jog button (PUSH LIST).
5. Press the function button 2 (ALL) to cancel the selection of all
tracks. (A check mark on the right side of track number will
disappear)
z
z
Содержание MEX-1HD - Audio Library System
Страница 123: ...123 MEX 1HD MEMO ...
