Sony IFB-LE100, Руководство по обслуживанию

Страница: 39 / 258

1-33
VPD-LE100A/LE100E/LE100U
20
Connection Examples
Connecting 15k RGB/Component Equipment
Note
Switch the input signal with the INPUT-A item in the
SIGNAL SELECT menu.
For details, see page 36.
STATUS/ERROR MESSAGE
IN
PLIG IN POWER
OUT RS-
232C
RS-
422A
RS-232C/422A PJ COM IN OUT
STANDBY 1 ON @
0 0
CONTOROL S TRIG DEVICE INDEX CONTOROL
0 0
CONTOROL S
IN
PLIG IN POWER
STATUS/ERROR MESSAGE
OUT
STANDBY
1
ON
@
RS-
232C
RS-
422A
RS-232C/422A PJ COM IN
R G/G SYNC SYNC/HD VD B
OUT
TRIG DEVICE INDEX CONTOROL
:
When making connections, be sure to:
• turn off all equipment before making any
connections.
• use the proper cables for each connection.
• insert the plugs of the cables properly; plugs that are
not fully inserted may generate noise. When pulling
out a cable, be sure to pull it out from the plug, not
the cable itself.
Also refer to the instruction manual of the equipment to be
connected.
Connection Examples
Connecting a BNC connector
2
Turn to the right.
1
Align the pins with the pin holes
and push in the plug into the
socket.
15k RGB/component
equipment
to RGB/component output
Monitor cable
(not supplied)
Rear
AC power cord
(supplied)
to AC inlet (front)
Signal flow
to INPUT A
(R, G, B)
to a wall outlet
(200-240 V AC,
15 A or more)
21
Connection Examples
0 0
CONTOROL S
IN
PLIG IN POWER
STATUS/ERROR MESSAGE
OUT
STANDBY
1
ON
@
RS-
232C
RS-
422A
RS-232C/422A PJ COM IN
R G/G SYNC SYNC/HD VD B
OUT
TRIG DEVICE INDEX CONTOROL
STATUS/ERROR MESSAGE
IN
PLIG IN POWER
OUT RS- 232C RS- 422A RS-232C/422A PJ COM IN OUT
STANDBY
1
ON
@
0 0
CONTOROL S TRIG DEVICE INDEX CONTOROL
:
OUT PUT
SW NO RS-232C/422A
REMOTE RS-232C
RS-422A RS-485 IN
RS-485 OUT
Connecting the Switcher
Use the optional PC-3000 Signal Interface Switcher
for connecting various video equipment. The input can
be selected by pressing the SWITCHER/VIDEO
MEMORY/INDEX keys on the Remote Commander
or the SWITCHER keys on the control panel.
For selecting the input from the switcher, see pages 9 and
13.
Notes
• When you select the input from the switcher, be sure
to set the SWITCHER/VIDEO MEMORY/INDEX
select switch on the Remote Commander to the
SWITCHER position.
• When connecting the switcher, use the wired Remote
Commander. If you use the wireless Remote
Commander, activate the remote control detector on
only one unit of the equipment connected through the
PJ COM connector. To deactivate the remote control
detectors of this unit, set SIRCS RECEIVER in the
SET SETTING menu to OFF.
For details, see page 36.
• After all the connections are complete, attach the
terminator (supplied) to the PJ COM connector on
both the projector and switcher to which nothing is
connected.
Device index
number: 01
Rear
to INPUT A
SIC-10 connecting cable
(5BNC
y 5BNC)
(not supplied)
to OUTPUT
PC-3000 switcher
Computer, etc.
to PJ COM
IN
RCC-5G/10G/30G
connecting cable
(not supplied)
to PJ COM OUT
Attach the
supplied
terminator.
to a wall outlet
(200-240 V AC,
15 A or more)
AC power cord
(supplied)
to AC inlet (front)
Signal flow
VCR, etc.
Attach the
terminator
(supplied with
the PC-3000).
To connect a single switcher
Connections