Sony IFB-LE100, Руководство по обслуживанию

Страница: 17 / 258

1-11
VPD-LE100A/LE100E/LE100U
20
0 0
CONTOROL S
IN
PLIG IN POWER
STATUS/ERROR MESSAGE
OUT
STANDBY
1
ON
@
RS-
232C
RS-
422A
RS-232C/422A PJ COM IN
R G/G SYNC SYNC/HD VD B
OUT
TRIG DEVICE INDEX CONTOROL
STATUS/ERROR MESSAGE
IN PLIG IN POWER OUT RS- 232C RS- 422A RS-232C/422A PJ COM IN OUT
STANDBY
1
ON
@
0 0
CONTOROL S TRIG DEVICE INDEX CONTOROL
SELECT
VIDEO MEMORY
SWITCHER INDEX
PIC ON AUDIO OFF
PATTERN FOCUS ZOOM SHIFT
NORMAL
MUTING
STATUS
LCD LENS CONTROL
ON
COMMAND
OFF
SIZE DOT PHASE APA SHIFT
RGB
R
B
CENT
ON STANDBY
MEMORY MENU
VIDEO
INPUT SELECT
A D B C
BLKG SYS SET RESET PUNCTION
1 4 2 3
5 8 6 7
9 10/0(ALL)
SW NO/
OFF/GBOUP
SWITCHER/VIDEO MEMORY /INDEX NO
ENTER
POSITION BRIGHT CONTR
PICTURE CONTROL
HUE COLOR SHARP VOLUME
VIDEO/S VIDEO
LIGHT
ON ON
Projecting
Projecting
Rear remote control detector
STANDBY indicator
ON indicator
1
2
4
3
4
1
Set the POWER switch on the front of the
projector to ON.
The STANDBY indicator lights in red and the
projector enters the standby mode.
2
Press the ON key.
The ON indicator lights in green.
3
Turn on the power of equipment connected to the
projector. Press the INPUT SELECT keys to select
the input source.
A: Selects the signal input from the INPUT A
connectors.
B: Selects the signal input from the connectors on
the optional interface board which is installed in
the INPUT B section.
C:
Selects the signal input from the connectors on
the optional interface board which is installed in
the INPUT C section.
D:
Selects the signal input from the connectors on
the optional IFB-LE100 interface board which
is installed in the INPUT D section.
Note
When you select the input signal connected to the
INPUT A, INPUT B, INPUT C or INPUT D
section, be sure to select the correct signal type on
INPUT-A, INPUT-B, INPUT-C or INPUT-D of
the SIGNAL SELECT menu. If an incorrect signal
type is selected, picture may be distorted.
For details, see “The SIGNAL SELECT Menu” on page
28.
When you input the signal from equipment
connected to the PC-3000 Signal Interface
Switcher (not supplied)
Set the SWITCHER/VIDEO MEMORY/INDEX
select switch on the Remote Commander to the
SWITCHER position and press the number keys 1
to 8 to select the input. When multiple switchers
are connected, press the SW NO/OFF/GROUP
key, then select the switcher number and the input
number.
STANDBY key
MUTING PIC key
SW NO/OFF/GROUP key
SWITCHER/VIDEO MEMORY/
INDEX select switch
Control panel (on the top)
21
Projecting/Adjusting the Picture
Adjusting the Picture
This section describes how to adjust the focus, size and
vertical/horizontal position of the picture.
1
Press the PATTERN key to display the HATCH
pattern.
2
Press the FOCUS key then the M or m key to
adjust the focus.
“FOCUS” appears on the screen during
adjustment.
3
Press the ZOOM key then the
M
or
m
key to adjust
the picture size.
“ZOOM” appears on the screen during adjustment.
4
Press the FOCUS key then the M or m key to
adjust the focus again.
“FOCUS” appears on the screen during
adjustment.
5
Press the SHIFT key then the
M
/
m
/
<
/
,
keys to
adjust the vertical/horizontal position of the
picture.
“PICTURE SHIFT” appears on the screen during
adjustment.
6
Press the PATTERN key again to clear the
HATCH pattern.
Notes
• The picture adjustments can be performed only when
FOCUS, ZOOM or PICTURE SHIFT is displayed on
the screen. If the display disappears, press the
FOCUS, ZOOM or SHIFT key again, and adjust with
the
M / m / < / , keys.
• Focus may drift depending on the temperature.
Therefore, we recommend you adjust the focus after
you have turned on the projector and projected the
picture for more than 30 minutes. Even after you
have adjusted the focus exactly, slight lack of focus
may occur when the lens is not sufficiently warmed,
e.g. immediately after the power is turned on. In
such a case, the correct focus is recovered by
projecting the picture for more than 30 minutes.
• If you cannot obtain the correct focus on the upper
and lower parts of the screen by pressing the M or m
key, the adjustment inside the projector may be
required. Please consult with qualified Sony
personnel.
To operate from the control panel, use the
SWITCHER keys 1 to 8 to select the input, and the
SW NO key to select the switcher.
Note
Press the SYS SET key when you make the system
connections using the PC-3000 switcher.
4
Adjust the size, position and focus of the picture.
For details, see “Adjusting the Picture” on the right
column.
To cut off the picture
Press the MUTING PIC key. To restore the picture,
press the MUTING PIC key again.
Caution
Do not look into the lens when the projector lamp is
on. Doing so may damage the eyes.
To turn off the power
1
Press the STANDBY key.
The ON indicator flashes in green and the cooling
fan keeps running for about 15 minutes to reduce
the internal heat.
When the fan stops running, the STANDBY
indicator lights in red.
2
Set the POWER switch to OFF.
Note
Do not set the POWER switch to OFF while the fan
is running. Doing so stops the fan before the inside
of the unit has not be cooled down sufficiently and
may damage the unit.